Historic American Engineering Record - Boston Elevated Railway Company photographs and information

From Wikisource
Jump to: navigation, search
Warning: This page does not provide {{Header}} information. If you'd like to help, add a comment, or edit the page and replace "{{no header}}" with the following and fill in at least the title and author fields:
{{header
 | title      = 
 | author     = 
 | translator = 
 | section    = 
 | previous   = 
 | next       = 
 | year       = 
 | notes      = 
 | categories =
 | portal     =
}}
Click here for a list of Author pages that link to this page.

Cover page[edit]

HAER
MASS
13-BOST,
127-

[above is handwritten]

HAER No. MA-14

Boston Elevated Railway Company:
Elevated Mainline Structure
(Metropolitan Bay Transportation Authority, Orange Line)
Boston
Suffolk County
Massachusetts

PHOTOGRAPHS

WRITTEN HISTORICAL AND DESCRIPTIVE DATA

Historical American Engineering Record
National Park Service
Department of the Interior

Washington, D.C. 20013-7127

Index to Photographs[edit]

Transmittal form[edit]

TRANSMITTAL FORM

Date: July, 1986

Project Name: Boston Elevated Railway Company: Mainline Elevated Structure (MBTA - Orange Line)

Staff Member Eric N. Delony, Principal Architect

Phone: 202-343-9629

Collection: HAER

State(s): Massachusetts

County(s): Suffolk

City(s) or Vicinity(s): Boston

Neighborhood or District: South End, Roxbury and Jamaica Plain

Site(s) and/or Structure(s): An Elevated Rapid Transit Railroad structure with Six Stations

Addendum: No

Sponsors: U.S. Department of Transportation, Urban Mass Transit Administration address and contact person unknown
Massachusetts Bay Transporation Authority, Southwest Corridor Project. 500 Arborway, Boston, Mass. Daniel L. Ocasio, Director of Design & Development, Southwest Corridor Project.
Kaiser Engineers/Fay Spofford & Thorndike (sub-consultants to MBTA) Six St. James Avenue, Boston, MA 02116, Charles D. Shaker, Manager, Urban Desgin

SHPO: Ms. Valerie Talmadge: Executive Director Massachusetts Historical Commission 80 Boylston Street Boston, MA 02116

Regional Directors: James W. Coleman Jr., Regional Director Mid-Atlantic Office, National Park Service 143 South 3rd, Street, Philadelphia, PA 19106

Comments: This report was compiled to serve as a mitigatory documentation of the structure to comply with the requirements of the Memorandum of Agreement, signed February 1978 by the Advisory Council on Historic Preservation; the Massachusetts Bay Transportation Authority (MBTA); Boston Landmarks Commission; Urban Mass Transportation Administration, and the Massachusetts Historic Preservation Officer. The preparation of this report has been financed in part through a grant from the U.S. Department of Transportation Administration, under the Urban Mass Transportation Act of 1965, as amended.

Site data form[edit]

United States Department of the Interior National Park Service Washington, D.C. 20240

HISTDRIC AMERICAN ENGINEERING RECORD SITE DATA FORM

STATE Massachusetts

COUNTY Suffolk

TOWN OR VICINTY Boston

HISTORIC NAME Boston Elevated Railway Company: Elevated Mainline Structure

HAER NO. MA-14

SECONDARY OR COMMON NAMES MBTA - Orange Line

COMPLETE ADDRESS (DESCRIBE LOCATION FOR RURAL AREAS) Washington Street, Boston, Mass. from Dover Street to Forest Hills and through the South End, Roxbury and Jamaica Plain.

DATE OF CONSTRUCTION 1898-1901 & 1906-1909

ENGINEER, BUILDER, OR FABRICATOR Engineering Department - former Boston Elevated Railway Company George A. Kimball - Chief Engineer

SIGNIFICANCE (TECHNOLOGICAL AND HISTORICAL, INCLUDE ORIGINAL USE) Elevated structure is the last remaining portion of a formerly extensive elevated rapid transit system built at the turn of the century in Boston.

STYLE (IF APPROPRIATE) Elevated structure to support rapid transit railway system (electric)

MATERIAL OF CONSTRUCTION (INCLUDE STRUCTURAL SYSTEMS) Tracks spiked to wood ties bolted to steel trusses (longitudinal) which are framed into transverse bents which in turn frame into two columns supported by concrete foundations on solid material under street.

SHAPE AND DIMENSIONS (SKETCHED FLOOR PLANS ON SEPARATE PAGES ARE ACCEPTABLE) See reproductions of original drawings.

EXTERIOR FEATURES OF NOTE Three variants of a then common elevated structure constructed of sections built up of riveted assemblages of rolled structural steel. Stations were designed in several styles (Beaux Art fashion) to adapt to the steel elevated structure.

INTERIOR FEATURES OF NOTE (DESCRIBE MECHANICAL SYSTEMS, MACHINERY OR EQUIPMENT) Trains were from four to eight cars long powered by electricity, gathered from a third rail and run by the "multiple unit" system of propulsion.

MAJOR ALTERATIONS AND ADDITIONS WITH DATES Dudley Station altered in 1908 and in 1948. Forest Hills extension opened for use in 1909.

PRESENT CONDITION AND USE Structure has lost 30% of its metal through corrosion but is presently structurally adequate for regular rapid train service.

OTHER INFORMATION AS APPROPRIAE The structure is currently in use but is slated for demolition in 1987, when it will be supplanted by a new relocated Organe Line.

SOURCES OF INFORMATION (INCLUDING LISTING ON NATIONAL REGISTER, PROFESSIONAL ENGINEERING SOCIETY LANDMARK DESIGNATIONS, ETC.) Information not available

COMPILER, AFFILIATION Cynthia R. Zaitzevsky, Consultant in Architectural History

DATE July, 1986

Body[edit]

HISTORIC AMERICAN ENGINEERING RECORD

BOSTON ELEVATED RAILWAY COMPANY - ELEVATED MAINLINE STRUCTURE (MBTA - ORANGE LINE)

HAER NO. MA-14

LOCATION:[edit]

The extant (1986) portion of the original elevated Mainline of the former Boston Elevated Railway Company (BERy) is located on Washington Street, in the South End, Roxbury and Jamaica Plain districts of Boston, Mass. and runs between the South Portal of the Washington Street tunnel and the Forest Hills Station, repair shops, and storage yards (Bents #1215 to #772). The original Mainline of the Boston Elevated Railway ran from Sullivan Square, Charlestown to Dudley Street, Roxbury and was later extended to the Forest Hills Station. The remaining structure consists of six stations. Bent numbers are indexed on plans in the files of the Massachusetts Bay Transportation Authority (MBTA) Engineering Department. Grid Coordinates refer to the Boston South Quad.

STATIONS GRID COORDINATES
1.) Dover Street (Bents #1174-1181) 19.0329780E.4689820N
2.) Northampton Street (Bents #1093-1098) 19.0328880E.4689000N
3.) Dudley Street (Bents #1024-1040) 19.0328260E.4688250N
4.) Egleston (Bents #908-915) 19.0328030E.4686760N
5.) Green Street (Bents #857-864) 19.0326500E.4686070N
6.) Forest Hills (Bents 783-789) 19.0325780E.4685100N

DESCRIPTION:[edit]

The Mainline of the BERy at one time consisted of six sections which traversed the congested areas of Boston and Charlestown to Roxbury and Jamaica Plain. For convenience these sections will be categorized alphabetically, according to their original loca tions, and hereafter will be referred to by Section letter. The main body of this report concerns Section F.

The sections are indexed on plans of the former BERy, MTA and the current MBTA. These plans have been included in this study as Fig. No. HD-1, HD-2, HD-3, HD-4, and HD-5.

* * * *

This report with the accompanying illustrations was compiled to serve as a mitigatory documentation of this structure in order to comply with the requirements of the Memorandum of Agreement, signed February 1978 by the Advisory Council on Historic Preservation; Urban Mass Transportation Administration; and the Massachusetts State Historic Preservation Officer.

* * * *

SECTION A

Formerly the Charlestown Division of the Boston Elevated Railway Company (BERy). Constructed in 1898-1901. Sullivan Square Terminal southerly through Charlestown to the North Portal of the subway. Included City Square, Thompson Square, North Station stations and the Charlestown drawbridge over the Charles River (built in 1896-1899 by the Boston Transit Commission). This section was abandoned in 1975 and was demolished in 1976-1977 when the new Orange Line subway was extended to Medford along the Boston and Maine Railroad right of way. Only Tower "C" was saved from demolition and moved to the Seashore Trolley Museum at Kennebunkport, Maine.

SECTION A-1

Extension of the Charlestown Division line easterly into Everett. Constructed in 1916-1919. Included only one station -- Everett (built by the BERy). Discontinued in 1975 and demolished in 1976-1978.

SECTION B

North Portal to Pleasant Street Station (now Broadway) via the outer tracks of the Tremont Street Tunnel which was adapted to elevated train use in 1901 by the construction of higher platforms. This 1ink was returned to full streetcar use in 1908 with the construction of the Washington Street Tunnel.

SECTION C

Pleasant Street Station, up the incline, over the Boston and Albany and New Haven Railroad right-of-way tracks, and along Castle Street as an elevated structure, to Tower "D" (Bent #1200) on Washington Street. Constructed by the BERy in 1901 to link the Washington Street elevated to the South Portal of the Tremont Street Subway. Abandoned in 1908. Demolished in 1935. Incline portion remained until demolition in 1961.

SECTION D

Elevated structure along Atlantic Avenue from Tower C at North Station to Tower D at Washington Street. Constructed in 1901 and in use until 1938. Demolished in 1942.

SECTION E

North Portal to South Portal via Washington Street Tunnel. Built in 1904-1908 by the Boston Transit Commission. This section will continue in use after demolition of the elevated structure.

SECTION F

South Portal to Forest Hills repair shops. This line was originally known as the Roxbury Division of the BERy. The line is divided for identification purposes into the following sub-sections:

SECTION F-l

South Portal (Bent #1215) to Tower D at Washington Street. Built in 1908 by the BERy to connect the new subway tunnel to the Washington Street line of the Roxbury Division. Structural system is plate girder bents with longitudinal plate girders.

SECTION F-2

Tower D at Bent #1200 to Bent #1143 south of Dover Street Station. Bui1t between 1899 and 1901 as part of the BERy Roxbury Division to Dudley Terminal. Plate girder bents with longitudinal truss girders.

SECTION F-3

Bents #1143 to #1068 along Washington Street. Built between 1899 and 1901 by the BERy. Includes Northampton Street Station. Arched truss bents with longitudinal truss girders.

SECTION F-4

Bents #1143 through #1100 to the Bartlett Street Yard. Built in 1899 to 1901 by the BERy as part of the original Roxbury Division. Includes the Dudley Terminal and the Guild Street yards and repair shops (discontinued in 1923). Plate girder bents with longitudinal truss girders. Loop around Dudley Station is marked by Bents T-l through T-28.

SECTION F-5

This section is the beginning of the Forest Hills Division. Construction work began on May 2, 1906 and service began on November 22, 1909. Work included rebuilding the loops and platforms at Dudley Street Station and the construction of Egleston Station. Section F-5 runs as an elevated structure from Bent #1000 to #797 at the Arborway yards. Construction is plate girder bents with plate longitudinal girders. was added on as a suspended structure in 1912. Green Street Station was added on as a suspended structure in 1912.

SECTION F-6

This section was a specially designed steel framework encased in concrete. Bents #979 to #783 include Forest Hills Station. Built in 1908-1909 by the BERy.

SECTION F-7

Bents #783 through #772 constitute the Forest Hills train storage yards and the repair shops. This extension was built in 1921. Repair shops built in 1923. Includes Tower "H". This section was demolished in 1984.

Dates of Construction:

Sections F-1 through F-4: 1898 - 1901

Sections F-5 through F-6: 1906 - 1910

Section F-7: 1921 - 1923

Engineers/Builders:

Boston Elevated Railway Company Engineering Department: George A. Kimball, Chief Engineer

Present Owner:

Massachusetts Bay Transportation Authority (MBTA) 10 Park Plaza, Boston, Mass. 02116

Present Use:

Remaining portion of the original BERy elevated Mainline Structure is currently in use as part of the MBTA's Orange Line rapid transit service from Forest Hills to Medford, Mass. The elevated portion (Section F-1 through F-7) serves from the South End through Jamaica Plain. The entire structure is slated for demolition when the new Southwest Corridor segment of the Orange Line rapid transit is completed.

Significance:

This portion of the Orange Line elevated is historically significant as Boston's first elevated line, built during a period of world-wide interest and experimentation with elevated railways; and as the product of Boston's last privately-owned transit company, the Boston Elevated Railway Company.

Architecturally, it is significant for the quality of its original station architecture, which was designed by the prominent local architect, Alexander Wadsworth Longfellow. Later alterations were carried out under consultation with other leading Boston architects, such as Robert Swain Peabody and Edmund Wheelwright. In general, it represented the most advanced transportation planning of its day and is a good case study, on a small scale, of rapid transit at the turn of the century.

Historians:

Cynthia Zaitzevsky - Consultant in Architectural History to Kaiser Engineers, Inc./Fay, Spofford and Thorndike, Inc. (Coordinating Consultants to the MBTA for design and construction of the new relocated Orange Line -- Southwest Corridor Project)

Christine Fernandez Carvajal - Research Assistant

Calvin Opitz - Assistant on Structural Engineering Portion

Nikita Zaitzevsky - Assistant

BOSTON ELEVATED RAILWAY COMPANY - ELEVATED MAINLINE STRUCTURE (MBTA - ORANGE LINE)

Submitted to the

HISTORIC AMERICAN ENGINEERING RECORD

by

Cynthia Zaitzevsky

Consultant in Architectural History to

Kaiser Engineers, Inc./Fay, Spofford and Thorndike, Inc.

Six St. James Avenue

Boston, Mass. 02116

for

Massachusetts Bay Transportation Authority

Contributing Authors:

Christine Fernandez Carvajal
Calvin Opitz

Nikita Zaitzevsky

The preparation of this report has been financed in part through a grant from the U.S. Department of Transportation Administration, under the Urban Mass Transportation Act of 1964, as amended.

TABLE OF CONTENTS[edit]

Orange Line Documentation

Chapter 1
Introduction and Discussion of Significance

Chapter 2
History of Early Public Transportation in Boston

Chapter 3
Construction of the Elevated Structure - 1898-1901

Chapter 4
Construction of the Forest Hills Extension

Chapter 5
Architectural Description of the Stations

Chapter 6
Structural Analysis and Description of the Elevated Structure

Bibliography

Appendix A
Chronological History of Orange Line up to 1918.

Appendix B
Description of the Early Electrical Systems (Abstract of Contemporary Description by Frank J. Sprague)

Appendix C
List of Historical Photographs.

Appendix D
List of Historic Drawings.

Chapter 1 Introduction and Significance of the Orange Line Elevated[edit]

Ever since Boston's earliest days Washington Street has been the main route for transportation between Boston and Roxbury and all other towns in the southwest portion of the larger city. The earliest stagecoach followed by the omnibus and later by horse-drawn and then the electric streetcar all used this route that was to become so heavily travelled that by the 1880's it had become imperative to build an elevated railway to provide rapid transit north and south of Boston. This section of the elevated structure from Dover Street to Forest Hills is the last remnant of a larger system of elevated railroads that served Boston at the turn of the century. Boston was one of the last major American cities to build an elevated rapid transit line.

The system was developed first in New York City and refined in Chicago, where third-rail electric motive power was first used.

Because it was built comparatively late, the Boston Elevated structure could use advanced rapid transit technology borrowed from many different sources. It is today a good case study, on a small scale, of the "State of the Art" of rapid transit at the turn of the century.

The Orange Line is significant not only from the point of view of techno1ogy but it also represented the most advanced transportation planning of its day. The BERy was the first company in the United States to include subways, elevated transit and surface trolleys -- all operating under one management. In contrast to a system with many competing lines and companies (the usual situation in most cities), the public could transfer from one section to another of the BERy without paying more than one fare.

The early history of the Boston Elevated Railway and the Orange Line illustrates how Boston avoided the excesses of both total public control and free-wheeling private enterprise. All major cities building transit systems at that time had such problems in common, but in Boston a balance was struck: private management ran the system but government regulated it and also built the subways.

Although it was a small system, Boston's distinctive topography caused many difficult planning and engineering problems. Narrow curving streets, high density in the downtown area, limited arteries into the center of Boston, the hilly terrain, the Boston Common and Public Garden, and settled residential districts made the task difficult for the Civil Engineer. Contemporary descriptions of the system continually extolled the work. It remains today an impressive undertaking. By studying this system today, we learn on a modest scale about the problems of other transit systems of that era. We can also more fully appreciate the engineering capabilities that built this system.

Chapter 2 History of Public Transportation in Boston[edit]

Unti1 the mid 19th century, Boston was a peninsula surrounded by water on three sides and connected to Roxbury on the south by a neck of land. Cambridge to the west and Char1estown to the north, connected to Boston by bridges, were the only other important communities. People lived close to their work and rarely travelled beyond their own communities. Except for private coaches and horses for the well to do, stagecoaches, omnibuses and, later, trains were the only methods of distant travel.

The omnibus, a horse-drawn bus with a rear entrance, was the first form of public transportation running on a regularly scheduled basis. In 1826 the first omnibus line in Boston opened. This ran to Cambridge, and by 1830 there was a similar line to Roxbury. Both were privately operated.

These early omnibus lines used approximately the same routes as at least two of the major branches of Boston's later public transportation system: The Red Line serving Cambridge/Boston and Orange Line serving Roxbury/Boston/Charlestown (HP-1) (For explanation of illustration designations, see Notes, Chapter 2.)

In 1856, the first horse-drawn street cars were introduced from Harvard Square, Cambridge to Bowdoin Square, Boston. Although steam railroads had been operating since the 1830s under charters from the Massachusetts Legislature, their service was limited largely to routes between cities and towns. By the middle of the century, Boston's population had increased greatly and there was a pressing need for rapid transit within the city.

The first such company was the Cambridge/Boston Company (1856), followed by the Metropolitan Railroad Line. This change underscored the evolution of Boston from a compact mercantile city to a larger one fed by the suburbs. Horse railways operating under a public franchise offered a faster and more comfortable ride than the omnibus. Under Massachusetts law, a franchise was a revocable right, granted by a municipality, to operate over public roads; thus the public had some control over the privately operated horse railways.

The Legislature and the Boston City Council subscribed to the then universal belief that free competition among many companies on public streets would provide the best service for the general public. In most large cities, especially New York and Chicago, there were many independent lines spread out over a wide geographical area. In spite of municipal corruption, the traction franchises still ensured reasonably good public service.

In Boston, because of local topography, the situation worked out differently. All traffic from the north and south was funnel led into the downtown along the two main downtown streets: Tremont and Washington. As Boston's population and business district grew, the surrounding towns became bedroom suburbs, and in turn caused the public transportation system to become overloaded.

By 1865 there were four main horse street railways:

  • The Middlesex Railroad - serving the North (Charlestown);
  • Union Railway - serving the West (Brighton, Cambridge, Somerville, Watertown, and Arlington);
  • Metropolitan Railroad - serving the Southwest (Brookline, Dorchester, Roxbury, West Roxbury);
  • South Boston Railroad - serving the South (South Boston, Dorchester).

In 1872 and 1881, the Highland Street Railway, serving Roxbury and Dorchester, and the Charles River Railway, serving Cambridge and Boston were established.

The lines were largely independent, and there were few crosstown lines or transfers. In the congested downtown area, the lines had to share a few tracks along Tremont and Washington Streets (HP-2, HP-3). Fragmented service and competing lines were not the answer to Boston's expanding business growth and population.

By 1860, traffic was 50 million riders, and, in 1885, it had climbed to 80 million. All large American cities had similar transportation problems and tried various solutions. In 1873, the cable car was invented in San Francisco and quickly was adopted in New York, Chicago and Washington, D.C. The horse-drawn street car had reached the limits of its effectiveness. It could not travel long distances at a high speed or carry heavy loads of passengers, and the cost of maintaining large stables of many horses was becoming prohibitive.

The cable car was the first practical method of increasing the effectiveness of mass transportation. Although the cable cars worked well in cities with broad straight avenues, they were not feasible on Boston's crowded streets, which had to carry several lines.

In Berlin, in 1881, Werner Siemens put into operation the world's first electric streetcar. This was followed by various attempts by Charles Van Depoele and Leo Daft in the United States to develop a workable electric streetcar.

The rapid development of technology in the 1880s provided a solution. The first practical electric streetcar system was realized by Frank Julian Sprague in Richmond, Virginia in 1887 -- a major step in transit history.

Meanwhile in 1886, Henry Melville Whitney, Eben Jordan and others had purchased a vast amount of land along Beacon Street in Boston and Brookline to develop as real estate. They also chartered the West End Railway to provide street car transportation into Boston. Whitney soon realized that a11 seven of the then competing roads would have to be combined into one economical line. His strong financial backing and his political role as an enlightened Democratic business man gave him the legislative support to create the requisite transit monopoly in Boston and its major suburbs.

Whitney, in less than a year, had organized the seven separate lines into a single integrated transit system using the "division system" of organization employed by major railroad companies. The best executives from the old lines were placed in responsible positions within the new company.

Frank L. Sprague's success with the electric street car in Richmond, Virginia convinced Whitney that electric traction was the solution to the shortcomings of the horse cars. He electrified the Beacon Street Line of the West End Railway in 1887, making Boston the first major city in the world to employ electric streetcars. By 1892, the trolley cars accounted for two thirds of the city use, and, by 1894, more than 90% of the lines were electrified (HD-100).

Contemporary accounts describe the progress of the West End:

Within a single year this company, through the financial genius of its organizers, had accomplished the consolidation of all the great street railway companies of the city, operating 231 miles of track, the largest street railway system in the world.... It is probable that more problems of mechanical engineering and of railway administration have been grappled 'ab initio' by this one company than by any other team of street railway companies in the last fifty years. [1]

Although the West End provided excellent transit service, there were still prob1ems. Ridership kept increasing, and the number of persons and streetcars going into downtown Boston began to choke the downtown streets again. There were many proponents of an elevated railroad to provide rapid transit. This had been the solution in New York City, where the first elevated railroad powered by steam locomotives was built. Chicago, another city with broad, long avenues, also had a network of elevated railroads beginning in 1892. Most Bostonians did not want the noise and ugliness of elevateds in downtown Boston, but the residents of outlying sections of the city were in favor of an elevated railroad that would shorten travel time into Boston. Charles Cheape has chronicled the complex struggles that went on in Boston as the public sought a solution to the traffic jams in downtown Boston. [2]

In 1891, the Legislature set up a Rapid Transit Commission to resolve the transit impasse. After many hearings and much research, the Commission made several recommendations for Boston's future transportation system. Three recommendations were especially important:

  1. North and South Stations should replace the numerous railroad stations then serving Boston;
  2. An electric streetcar subway should be built under Tremont Street;
  3. A system of elevated and subway lines should be built to Char1estown, Roxbury, Cambridge, and Boston.

Stat. 1894 Chap. 548 -- An Act that incorporated the Boston Elevated Railway Company (the "Meigs Charter") and authorized numerous transit routes in the Boston Metropolitan area -- was the first regional approach to mass transportation. Later Acts were:

  1. Stat. 1895 Chap. 440 -- An Act that authorized the construction of subways in the City of Boston;
  2. Stat. 1896 Chap. 492 -- An Act that placed limits on the West End Railway in its use of the subway;
  3. Stat. 1897 Chap. 500 -- An Act that authorized the Mass. Railroad Commission to use other systems besides the Meigs. This law also:
    • a) Authorized construction of the Cambridge Subway;
    • b) Laid out routes of a proposed elevated railway;
    • c) Gave the Mayor of Boston authority to review and approve architectural and engineering plans of an elevated railway;
    • d) Established a five-cent fare with right of free transfer;
    • e) Required that the elevated railway run through a subway in the center of Boston;
    • f) Authorized construction of a new rapid transit bridge from Boston to Cambridge across the Charles River;
    • g) Authorized construction of a rapid transit tunnel to East Boston under Boston Harbor;
    • h) Declared franchise rights of the BERy to be irrevocable.

This was an unusually comprehensive and well thought out law that resolved most of Boston's transportation dilemmas. From this point on, good public policy and sound traction management were to be characteristic of the city's transportation system for many years to come.

After Henry Whitney left the West End Railway in 1893, that company lost its strong direction and failed to take advantage of the new legislation. A competing group of financiers headed by J. P. Morgan bought out the old Meigs franchise through the Boston firm of Kidder Peabody in 1895. The new directors had the requisite backing to finance construction of the "Elevated." They also proved able to overcome the public's objection to the structure. After some maneuvering, the Morgan group bought control of the West End, which, on December 9, 1897, was absorbed by the Morgan run Boston Elevated Railway. The new BERy now had both a financial and legal monopoly over most public transportation in Boston and its suburbs.

The Act of 1897 also resolved the dispute over the location of the Elevated structure. In 1895, the Boston Transit Commission had begun construction on the Tremont Street Subway, which opened on September 1, 1897. The new charter allowed the BERy to use the Tremont Street Subway for its elevated trains. This solution prevented the disfigurement of downtown Boston by elevated tracks while providing for their construction in the outlying suburbs of Roxbury and Charlestown.

The creation of the West End Railway and the BERy had understandably caused many reform minded individuals, led by Louis D. Brandeis, to fear that these giants would abuse their potential monopoly powers. It was a complex dilemma. There was little confidence in the ability of the often corrupt municipal governments to operate public transportation. Therefore the prevailing sentiment favored private enterprise. Yet only a company with near total monopoly powers could operate rapid transit systems effectively. Boston's eventual solution of pub1ic and private control was unique in the United States.

In other major American cities, traction companies managed to wrest total control from the public. By contrast, in Europe, muni cipal governments subsidized and completely controlled public transportation.

In Boston, the public component was the Boston Transit Commission chartered by the State Legislature. The Commission built the subway and leased it to the BERy to be used by its rolling stock. Thus the major capital expenditures for subway construction (more costly than an elevated structure but more desirable for use in the downtown area) would be undertaken by the City of Boston using its lower interest rate on bonds. The BERy, with the approval of, the State and the City, then built the elevated structure and connected it to the subway. With its impressive financial resources, it could build the structure, the stations and the outlying street lines and operate the entire system. The public benefited because the monopoly was partially under control of the electorate. The individual rider benefited more directly from the five-cent fare and the right of free transfer.

NOTES Chapter 2[edit]

  • [1] The Street Railway System of Boston - Street Railway Journal - April 1895.
  • [2] Charles W. Cheape, Moving the Masses - 1980.

References to illustrations are designated as follows:

HP-l through HP-ll? refer to Historic Photographs and are indexed in Appendix "C."

HD-l through HD-I00 refer to Historic Drawings and are indexed in Appendix "D."

MA-14-1 through MA-14-85 refer to Contemporary Photographs and are listed in the "Index to Photographs."


Chapter 3

Construction of the Elevated Structure 1898-1901

Once the legal problems surrounding the granting of a clear charter to the

Boston Elevated Railway and its franchise to build a third-rail, electrically operated, elevated rapid transit system (using the then new multiple unit cars)

had been resolved, the management of the BERy immediately began planning work for the proposed elevated structure.

George A. Kimball (1850-1912), a respected local civil engineer, was

appointed chief of the Engineering Division to plan, design and construct the

elevated railway.

Kimball had served for eleven years as chief engineer for the

City of Somerville and had gone on to distinguish himself as the engineer for

the Metropolitan Sewage Commission.

I n the 1880 I s thi s agency had been pri-

marily responsible for building a vast regional sewage system for metropolitan

Boston -- a major civil engineering feat for its day.

Under the terms of Chap. 500 Acts of 1897, the BERy was fi rst requi red to

submit plans of the route to the Massachusetts Railroad Commission, which at

that time was empowered to supervise all railroads and street railways, for

review and approval.

The plans then had to be approved by the Mayor and Common

Council of the City of Boston.

The main public criteria" were that the structure be light and airy and that

the stations be of superior architectural appearance.

Although New York City

had been constructing and operating elevated railways since 1873 and Chicago

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 25

since 1885 (HP-4), Boston was just now accepting this already standard form of

rapid transit.

New York's system of steam locomotives pulling wooden railroad

cars had not impressed Bostonians.

The structure of the New York Elevated

(HP-5, HP-6), though elegant and open in the early stage of development, became

less attractive as solid plate girders were used in the later extensions.

The

combination of noisy, smoky, dirty trains runnning over structures that blocked

out the sunshine on the streets below was something that Bostonians wished at

a 11 costs to avoid.

Moreover, with its sophisticated architectural and civil engineering forms,

the Berlin elevated railway system set a standard of excellence which Bostonians

tried to achieve (HR-14). [1]

The BERy executives made every effort within

their limited budget to avoid the mistakes of the New York systems and to emulate the successes of the Germans.

The basic design of the elevated structure was quite similar to the one

developed in New York City (HP-7) and later perfected in Chicago.

The prel imi-

nary designs were done under the direction of J.A.L. Waddell, who had been pri-

marily responsible for the design of the Chicago system.

The structural and

civil engineering work was done by the Engineering Department of the Boston

El evated Railway Company.

(Chapter 6...Structural Analysis and Description of

the Elevated Structure discusses in greater detail the engineering aspects of the elevated structure.)

In general, the tracKs were laid 24 feet apart on center except on narrow

streets where they were 12 feet apart (HD-15).

The rai ls were 85 lbs ASCE

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 26

sections spiked to hard pine ties 16 inches on center, which in turn were bolted

to the steel structure.

Every fourth tie was extended out to support a sidewalk

for track maintenance men.

The trackwork was supported on bents consisting of

steel columns supported on heavy concrete foundations.

Heavy cross girders con-

nected the columns and longitudinal gi rders with cross bracing supported the

tracks.

After a long design review process, the final approval for the system

came on April 29, 1898.

Construction began on the Dudley Station site on January 23, 1899. Property condemnation proceedings had already commenced allowing for demolition

of any structures in the way. Contracts for steelwork along the Roxbu ry Division were awarded primarily to the Pencoyd Bridge Co. of Pencoyd

Pennsylvania, a noted bridge building company, which already had considerable

experience with the then new steel technology of fabrication and construction.

Other steel work was executed by the Carnegie Steel Co. and the Pennsylvania

Steel Co.

Terry and Trench Co. of New York City were selected as general

contractors for the steel erection primarily because of their experience in

putting up elevated railroad structures in New York City.

While construction on some parts of the Elevated, in Charlestown and on Pleasant Street and Atlantic Avenue (HP-26, HP-27), was carried on in a normal

fashion during the day, most of the work on the Washington Street segment was

done at ni ght.

While efficiency and speed were considerations, the main reason

was to avoid touching the live wires that fed the trolley cars running along

Washi ngton St reet.

(The lines were either removed from the portion under

construction at night or else the power was cut.)

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 27

The BERy specifications stipulated that, wherever there were surface tracks, materials should be delivered to the narrow portions of the streets each

evening after 7pm and that construction could take place only between the hours

of midnight and Sam.

Co 1 umns and gi rders were fabri cated in the 'shops of the

bridge companies doing the work, delivered by railroad car to the nearest

siding and finally hauled to the site by trucks pulled by horse teams (HP-24).

Photographs show how the fi rst columns were erected on Washington Street near

Dover Street (HP-19).

After the cross members were in position, a traveller was

installed to lift succeeding bents into place.

Incandescent lights were also

hung from the traveller.

All steel members were riveted together. As each bent

was set into place and the longitudinal girders attached, the traveller pulled

itself forward along the tops of the girders on rollers to the next stop and installed the next section (HP-2l, HP-22).

The work was carried out in five segments (HD-l): a.) The Charlestown Main Division;

b.) The portion over the Charlestown Bridge which itself had been built in 1895 by the Boston Transit Commission;

c.) The conversion of the Tremont Street Subway, which originally consisted

of four tracks for streetcars and was modified by the BERy to allow use

of the high platform third rail trains on the two outside tracks;

d.) Building an inclined connector between the tunnel portal at Pleasant

Street across the Boston and Albany Railroad tracks and Tower D at

Washington St. (HP-9, HP-ll, HD-5);

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 28

e.) The construction of the Roxbury Main Line along Washington Street (now called the elevated portion of the Orange Line) to the terminal at

Dud 1 ey St reet.

The line was planned as an elevated rapid transit railway between several stations spaced at long intervals for passengers arriving by surface streetcars.

Since Boston streets were too narrow to allow more than two tracks, the New York

and Chicago system of four-track lines consisting of express trains and local

trains was not used.

Since the BERy also had the unique advantage of

cont ro 11 i ng all 1 oca 1 1 i nes with the ri ght of free transfer, the system of a

limited number of stations spread far apart was feasible.

The Roxbury Division

was planned to service local lines at Dover Street, Northampton and finally

Dudley.

These street car lines served Brookline, Newton, Dorchester, Roxbury,

Jamaica Plain, South Boston, and connected to other companies serving com-

munities to the southwest of Boston as far as Walpole.

Li nes that formerly ran

into downtown Boston either along the streets or, after 1898, through the

Tremont Street Subway were now serviced by the Elevated, thus cutting down the

time of travel.

Construction on the Castle Street/Pleasant Street connector began in the

fall of 1900 just as the work on the Pleasant Street portal and the new viaduct

was mostly done.

Construction photographs show the rapid progress of steel

erection during Oecember 1900 and January 1901.

To accommodate the longer

multiple unit, three car trains inside the Tremont Street Subway, the outer two tracks were converted to third-rail use; and, inside each Subway station, high

wooden platforms were erected to allow direct access to the trains.

Si nce the

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 29

Subway had been designed with short trolley cars in mind, some of the radii were too tight, and certain walls and platforms had to be modified to allow clearance

for the new trains.

Most of the conversion work was done in the Subway in the

week prior to the opening of the new elevated line in order to minimize obstruc-

tion to trolley cars uSing the Subway (HP-12, HP-13, and HP-18).

Steel erection on the Washington Street section began on AU9ust 19, 1899,

and, by December 20, 1899, the structure had been erected as far as Sterling

Street -- a remarkably fast performance by today's construction standards.

(In

1980, a modern flat plate girder replaced the existing trussed girder to allow

for the passage of the new Melnea Cass Boulevard under the structure (HP-40,

MA-14-27)) .

Project planning was done under what we now call a fast-track method.

As

soon as planning approvals were obtained, structural design and detail drawings were begun, and contracts were signed with steel companies for the required ton-

nage of steel.

First column foundations were poured.

Erection of the structure

began as soon as possible.

The main line structure was already up while archi-

tectural drawings for the stations were being completed.

A completion date of

December 1900 had originally been scheduled but was delayed a few months.

The

construction progress photographs show a last minute push in the winter of 1901

to finish the stations and other facilities. Concurrently with this work, the

8ERy was erect i ng the At 1 anti c Avenue loop (Sect ion D). wh i ch joi ned the North

and South Terminal Railroad stations and created a downtown transit circuit

through the Tremont Street Subway (Section 8) (HP-15, HP-27).

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 30

Dover Street Station was built in 1900 as a center platform type of struc-

ture.

Like Northampton Street Station, it was designed to be used by four-car

trains. After the opening, traffic on the elevated line was so heavy that the BERy decided to lengthen the station platforms to accommodate six-car trains

originally and eight-car trains later (HP-30, HP-31, HD-50 through HD-54).

Schematic plans were drawn from 1906 on for extending platform lengths and

i ncreas i ng the station's capabi 1 it i es of handl i ng more passengers.

The final

plan of July 1909, in which the center platform and station were removed, the tracks brought close together, and a new station built flanking the tracks, was

carried out.

The same plan shows that the center platform and waiting room were

eliminated (HD-58). When work was completed, the platform had been lengthened

to accommodate an eight-car train.

While the new pavilion with waiting room and change booths on the inter-

mediate level with the enlarged station meant a more functional plan capable of moving large numbers of passengers from streetcars to elevated train, the final

architectural configuration of the station that emerged was clearly inferior to

that of the first.

In April 1911, plans were issued for the erection of a temporary Oover

Street Station built of wood that would temporarily replace the regular one

while the complete renovations were under way (HP-32). [2J

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 31

Northampton Street was built according to plan and opened in 1901 and remains today as the only station that has undergone little change other than

the lengthening of the platforms to accommodate six-car trains in 1908 (HP-34,

HP-35, HP-36, HP-37, HP-39).

Dudley Station Dudley Station was conceived as the southern terminal of the Main Line.

Storage and repair yards were built at Bartlett Street, and a three-track spur

extended from Dudley station along Washington Street to join them. The terminal

itself was a complex tri-level combination of elevated train platforms and sur-

face and intermediate-level platforms for transfer to street cars. This terminal serviced all the streetcars coming to Dudley Station from Jamaica Plain,

Roxbury, West Roxbury, and parts of Dorchester.

Southbound tra ins from Su 11 i van

Square would arrive at Dudley, go around the loop, and pull into the northbound

platform to unload and load passengers.

These passengers came from streetcars

that rode up the inclines feeding the east and west loops which acted as

passenger platforms (HP-77).

On the surface level, there were other surface

lines bearing passengers.

All these surface lines could take passengers as far

out as Dedham, Westwood and Walpole(HP-41 through HP-50). [3]

The communities to the southwest of Boston were now more populous, and the

original spine of Washington Street to Roxbury (now called the "Orange Line")

extended beyond the Boston city limits.

By 1900, the BERY decided to build a

separate tunnel under Washington Street to connect the two ends of the Main Line

with a direct link.

Also the Tremont Street Subway could be returned to its

former use as as streetcar subway.

The Acts of 1903, Chap. 534 authorized the

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 32

Boston Transit Commission to build the tunnel and lease it back to the SERy, which would in turn furnish the tracks and operating equipment.

In retrospect, this decision seems wise.

In its implementatlon, it repre-

sented another stage in the continuing struggle between the management of the BERy and the reform elements in Boston who feared the monopolistic potential of

such a huge corporation.

While the construction of the tunnel was done by the

Boston Transit Commission, the interiors of the tunnels and the station fur-

nishings were the responsibility of the SERy.

The designs for the interiors and

entrances were carried out under the direction of the noted Boston architect

Robert S. Peabody.

The tracks and related equipment were designed and installed

by the Engineering Department of the BERy under George Kimball.

Similarly the

connection from the South Portal to the main line at Tower 0 (HP-16, HP-17) were

also the responsibility of the BERy's Engineering Division as was the super-

vision of construction.

The design of the tunnel station platforms allowed the

use of eight-car trains along the entire line, and plans were undertaken to

1 engthen the pl at forms at all stations.

During 1903, the BERy decided to extend the elevated structure to Forest

Hi 11s.

Again approval was sought from the Massachusetts Railroad Commission,

which held the requisite public hearings, and from the Mayor and Board of

Aldermen of the City of Boston.

The approval for the structure with locations

of stations was received on January 4, 1904.

Soon after that date, engineering

drawi ngs were undertaken.

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 33

NOTES Chapte r 3

[1] For a more complete description of the Berlin Elevated Railway see: Report of the Rapid Transit Commission to the Massachusetts Legislature, April 5, 1892. This description was written primarily by Commission Member Congressman John E. Fitzgerald.

[2]

[3]

The temporary Dover Street Station opened in July 29, 1912 and renovation work on the old station began. The new station opened December 7, 1912.

On December 28, 1908 the platforms had been extended enough to allow eight-car train service. �

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 34

Chapter 4

Forest Hills Extension

The extension of the elevated to Forest Hills was structurally less

complex.

With the exception of the Arborway crossing, plate girders, framed in

both directions, were used in the structure.

There are no extant contemporary

records that explain this decision.

Presumably economics dictated the use of a Remnants of transmittal letters (in the

cheaper but less attractive system.

MBTA fil es) i ndi cate that the st ructure was approved by the Mass. Railroad

Commission and by the City of Boston, and construction began on May 2, 1906 with

the erection of the first bents at Guild Street (HD-37). [1]

The same system that had been used earlier on Washington Street -- bents

delivered to the site during the day and set in place by the traveller at night

-- was employed.

Numerous construction photographs and drawings illustrate how

the work progressed and reveal the methods of steel erection and track laying

at that time (HP-78 through HP-90).

Again, progress in steel erection was rapid.

By late August of 1906, the

traveller had reached the Egleston Square station area and, by January of 1907,

the structure was approaching Forest Hills.

At this point, the chronology be-

comes unclear.

The BERy annual report of December 31, 1906 notes that the com-

pany had not yet received approval for plans for new stations at Egleston and

Forest Hills nor the changes at Dudley.

Presumably, the management was preoc-

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 35

cupied with the extra work on the Washington Street Tunnel and the numerous other projects then starting in Cambridge and East Cambridge.

Robert S. Peabody's daybooks for 1907 indicate that the BERy's committee of

architectural advisors met repeatedly during that year reviewing designs, not

only for Forest Hills Station and the Arborway crossing, but also for the

Causeway across the Charles River to East Cambridge. [2]

By early 1908, the

designs for all stations had been approved, and work resumed on the elevated

structure crossing the Arborway and on the Forest Hills Station itself.

Peabody, the chief architect to the BERy, appears to have decided to have a

line of single massive piers supporting the main line structure.

At this point,

where the structure crossed the Arborway, the piers would be encased in concrete

and made to look like rough hewn stone.

Peabody and his committee of architec-

tural advisors chose the same solution for the BERy crossing over the Charles River Dam (the Lechmere extension), which was designed at the same time.

The crossing of the Arborway (HP-103) was a particularly sensitive design

problem, since the architects wished their structure to harmonize with both the

landscape design of Frederick Law Olmsted and the nearby Forest Hills Railroad viaduct, a massive granite bridge designed by Shepley, Rutan and Coolidge from

preliminary plans by the landscape architects and constructed approximately ten

years before.

Peabody chose concrete treated to simulate masonry as a suitable

compromise (HP-116).

This BERy station was also intended by the Mass. Railway

Commission to connect with the then important Forest Hills commuter railway sta-

tion and the West Roxbury branch line of the New Haven Railroad.

.

.

.

Boston Elevated Rai lway Company HAER No. MA-14 Page 36

The new design for Dudley Station took an already sophisticated multi-level

scheme and enhanced it.

A new southbound platform for trains going to Forest

Hills was constructed over Washington Street along the West Loop of the ter-

minal.

The mainline continued out toward Guild Street and along Washington

Street to Egleston Square.

Two new pedestrian bridges connected a new south-

bound platform with the existing terminal.

The northbound platform built in

1900 was lengthened to receive the longer eight-car trains (HP-74).

At the same time, nUmerous changes were made on the surface level.

The

most interesting additions consisted of the two pavilion-type waiting rooms that

were placed inside the old loops (HP-70).

The trolley loops were also enclosed.

Work on the new platform began in the summer of 1908.

November 22, 1909 was the

opening date for extended service from Forest Hills to Sullivan Square.

Yet we

know that heavy steel work was still in progress under the southbound platform

after that date.

Progress photos show that, while the new platform and bridges

were almost complete, work on the framing of the new loop enclosures was just

beginning in October of 1909. Work on Dudley Terminal was essentially completed

by the summer of 1910, but final roofing was still being done in September of

that year (HP-61 through HP-68).

Dudley Terminal has always been a busy area, and minor changes have

constantly been made in the interior to improve passenger flow and expedite

movement of transit vehicles.

In 1948 the east pavilion was completely rebuilt

to allow use of the trackless trolleys that were replacing the old electric

streetcars in the Roxbury/Dorchester area.

The center pavilion was removed and

a new roof with factory skyl ights installed.

Gradually the service at the West

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 37

loop was phased out.

In the early 1970's, that loop was completely demolished.

Old photographs are the only record of the appearance of Dudley Station in its

prime.

By the 1960's, the MTA had substituted bus service for the trackless

trolleys.

The surface area under the station (Ziegler Street) formerly used by

trolley lines became a major bus connector (MA-14-28 through MA-14-43).

Egleston Station was planned to relieve Dudley Terminal and serve as a collection point for passengers coming in by streetcar from points in Jamaica

Plain and Dorchester.

In its construction, concrete passenger platforms were

used for the first time on the line.

Ori gi nally a stairway descended ri ght into

the middle of Washington Street at the intersection of Columbus Avenue.

In 1916

a trolley barn built with a low cost factory type of construction was added as

a station for surface loading of passengers.

A bridge and escalator connected

the new structure with the existing structure (HP-93 through HP-97).

The

architect for the station is unknown.

Forest Hills Station was an extension of the Arborway crossing of the main

1 i ne.

Designed by the architect Edmund S. Wheelwright, a member of the advisory

committee, under the direction of R.S. Peabody, it was framed of heavy steel

encased in concrete.

The BERy built an extension of the regular steel bent

construction system, beyond the station, to allow trains to reverse direction over a diamond shaped crossover. This work also included construction of a

spur-track incline out over the present Arborway yards for storing trains.

On

November 5, 1921, the Forest Hills station structure was extended southward. A

storage yard was built, and the Arborway inclined yard was removed.

By 1923, a

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 38

new car repair shop had been built which replaced the smaller shops and storage

yards at the Guild Street yard (HP-104 through HP-ll7). [3]

Green Street Stat ion

When the BERy submitted its first proposals for the Forest Hills extension

to the Mass. Railroad Commission, the plans included a site for a passenger sta-

tion at Green Street, but that particular location was not utilized at first.

It was only after the extension had been opened that the BERy decided to build

Green Street Station in 1910. The simplest construction method was used: a

suspension system of hanging the lobby from the bottom of the tracks and

building a steel-frame concrete platform with canopy on top of the structure. The station was completed and opened in 1912 and served as a local station for

commuters from the neighboring sections of Jamaica Plain (HP-98, HP-99).

Egleston Square Sub-Station The extension of the Main Line to Forest Hills required the construction of

a sub-station at Egleston Square for the conversion of alternating current

generated at the South Boston Plant to direct current for use in this portion of

the rapid transit system.

The station was designed by Robert S. Peabody and

consisted of a steel framed building to house the sub-station equipment.

The

exterior was of stucco trimmed in brick (MA-14-56).

.

.

.

[1J

[2J

[3J

Boston Elevated Railway Company HAER No. MA-14 Page 39

NOTES Chapte r 4

Copies of Letters of Transmittal between the BERy and various governmental agencies are on file in the MBTA Plan File Room.

Robert S. Peabody, Daybooks, 1907-1909. Courtesy of Professor Wheaton A. Holden, Northeastern University, Boston. The committee consisted of Boston architects Charles A. Coolidge, Charles D. Maginnis, Clarence H. Blackhall, Ralph Adams Cram, and Edmund M. Wheelwright under Peabody's di rection.

For additional information on the Forest Hills Station see the September/October 1984 issue of Rollsign (BSRA). �

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 40

Chapter 5

Architectural Description of the Stations

The orginal way stations of the Boston Elevated Railway were conceived as

parts of a single theme, designed by a single architect, and constructed over a

short period of time.

They refl ected a much more uni fi ed concept than the

stations that stand today.

Indeed, the winning design submitted by Alexander

Wadsworth Longfellow, Jr. (1854-1934) was often illustrated in trade journals by a single, "typical station" (HP-8). [1]

The style of each station was "early French Renaissance," combining classi-

cal and Gothic features in true Beaux Arts fashion.

The result, everyone

agreed, was appealling for the "I ightness, symmetry and beauty" of the stations

themselves and of their relationship to the graceful, web-like structure that

weaved over the streets of Boston.

The "typical station" of 19D1 dotted the original line between the Sull ivan

Square and Dudley Street terminal stations.

Subsequent alterations have

obscured the original Longfellow design. Of the "Roxbury Division's" first sta-

tions -- Dover, Northampton and Dudley Street stations -- only Northampton Street

has retained its original character.

It reveals perhaps the most enduring merit

of the original design:

stations of competent but unremarkable design, which

were adapted in every sense to thei r site:

the elevated structure.

The qual i-

ties that are aesthetically noteworthy in the elevated structure -- the sense of

motion, light and air; the expressive, curvilinear grace of the truss-work;

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 41

subtle adaptations to the site; rhythmic, elegant arches and carefully crafted details -- are also found in the stations.

DOVER STREET AND NORTHAMPTON STREET STATiONS

Dover Street and Northampton Street Stations were originally "island" stations, perched between two tracks on top of the elevated platform, enclosed

in rectangular huts with Renaissance details.

Northampton Street Station was

approximately 12 1/2 x 40 feet long, and Dover Street station was slightly

longer.

Each had a covered platform 160 feet long, and was sheathed in copper

panels and capped by an overhanging copper-paneled ridge roof brindled with

standi ng ri bs.

Standard features were three dormer windows and a central Beaux

Arts cupola flanked by two finials, one over each gable.

On the east and west

elevations, a band of sash windows (configured slightly differently at Dover and Northampton Street Stations) was surmounted by a diamond-paned clerestory and

separated by copper paneled pilasters decorated with a diamond motif.

The

di amond motif was repeated on the copper panel s just beneath the windows and

pilasters (HD-52 through HD-63).

The stat ions were reached by means of iron stai rways of approxi mate ly 38

steps, covered by a running copper canopy that was ribbed like the station roof.

Each landing was covered by a copper pavilion roof supported on four posts and

decorated with a copper finial.

A wrought iron balustrade enclosing the stair-

way on either side was decorated with scrolls and copper panels.

At the first landing, the passenger entered an arched double door with

diamond-paned lights and semi-circular transom.

The second flight of stairs led

.

.

.

Boston Elevated Rai lway Company HAER No. MA-14 Page 42

directly to the waiting room lobby, where the passenger purchased his ticket at

the ticket office.

He waited for the train inside the waiting room (similar to

HP-38) or outside the station on a canopied platform.

(When he disembarked on

the opposite side of the platform, he descended a connecting exit stairway which

led directly to the street.)

The station interiors were sheathed in oak, with hard pine for the floors

in both the station rooms and platforms.

The furnishings, also designed by

Longfellow, included a ticket office, turnstiles, wooden benches, porters' clo-

sets and rest rooms.

The ticket offices, octagonal or semi-octagonal booths

that stood in front of the entrance stairs, were distinguished by their classi-

cal detailing, elaborate iron work and varied materials.

To either side of the

ticket window were arched, sash or spring-balanced windows.

Decorating the

ticket window were a keystone and scrolled, wrought-iron grille. A thick marble

slab served as the ti cket ledge.

The lower portion of the office was sheathed

in wood and copper, and stood on a base of wood and Tennessee marble.

At Dover

Station the ticket office was originally crowned by an oak balustrade with

knobbed posts above a paneled architrave.

In the early days of operation of the

trains, passengers first bought a ticket and surrendered it at a turnstile

(HD-61, HD-62, HD-63).

In the center of the room were a pair of back-to-back wooden benches. Beside these were the rest rooms and porters' closets. Oak sheathed the interior

walls and separated the sash windows.

The ceiling, also sheathed in oak, was

patterned in the center panels with the diamond motif. Incandescent and arc

lights illuminated the interior (HP-38).

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 43

The platforms were notable for the quality of their engineering details.

(MA-14-22) .

DUDLEY STATION

Dudley Station, the southern terminal until 1909, was designed to harmonize with the way stations, punctuate the elevated railway with a strong design, and

meet the requirements of its function as a turn-around, transfer station and

junction of several surface lines.

Its complex vehicular circulation was

explained in a Boston Elevated Railway Company publication:

The rapid-transit track passed through the center of

the station, with a loading and unloading platform on

each side.

Surface cars reached the same level as that

of the rapid-transit platforms by easy inclines, a loop

track being provided on either side of the station so

that transfers between surface cars and rapid-transit

trains could be readily made.

Through cars ran through

the lower level of the station and the upper level was

reached by an adequate number of sta i rways. [2]

The elevated platforms to either side of the station were covered by copper

canopies which flanked the station below the clerestory and extended north on

the east and west sides.

The central, rapid-transit entrance on the north end

was arched and flanked by stairways which led to the surface level.

Two cupolas

surmounted the station's ridge roof; and a finial stood on each gable (HD-64

th rough HD-69).

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 44

To either side of this entrance were enclosed waiting rooms. each 18 feet

square and surrounded by paired, sash windows with diamond-paned upper sashes

(HD-70 through HD-73).

The exterior elevation was framed by a row of copper panels

and pilasters embellished with the diamond-triangle motif.

Set in the north-

easterly and northwesterly corners of the station, these waiting rooms were entered

via the elevated loading platforms under the station's main roof.

The exteriors

featured a ribbed mansard roof and an entrance decorated with classical ornament, a

tympanum with a paneled roundel, a scrolled arch, and a finial.

The interior was

paved with terrazzo.

The central loading platform was spacious, elegant and richly furnished. In addition to the two enclosed waiting rooms, it housed a magazine and tobacco

stand (HP-49), storage rooms, a ticket office, public toilets, built-in wooden

seats and, to either side of the platforms, wrought iron stairways leading to

the central waiting room, just below track level.

An oak ceiling was carried on a series of open steel trusses gracefully

arched and supported below the clerestory on copper brackets.

The a rch theme

was continued in the station walls, which were open to the unloading platforms

outs i de the stat i on vi a an arcade cons i st i ng of uncovered steel columns and

copper-paneled arches springing from copper brackets.

The a rches we re

embellished with keystones and copper-paneled roundels in the spandrels.

Above

these were rectangular paneled spandrels with a triangle/semi-circle motif, and

a clerestory of diamond-paned sash windows (HP-50, MA-14-36).

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 45

In the center of the room, to either side of the platforms, iron stairways

provided access to the central waiting room on a level below the track.

This

was an octagonal room, approximately 160 feet in diameter.

Richly articulated,

it featured an oak dado with stone mouldings, buff brick walls, a maple floor

and a coffered oak ceiling.

In 1909 Dudley Street Station was altered to provide for separation of

loading and unloading traffic, and for the accommodation of eight-car trains. The east and west loops were rebuilt, each containing a polygonal waiting room

pavilion (HP-69).

These had circular clerestories of paired, diamond-paneled

windows, a copper pavilion roof with standing ribs and a finial on top.

The

interiors were lined with built-in wooden seats.

A po lygona 1 wooden bench,

shaped like the exterior of the pavilion, stood in the center.

The wa 11 s we re

sheathed in oak, and were decorated with paneled arches and keystones.

New

loading and unloading platforms were built, accessible by new covered bridges

with stairway connections (HP-68 through HP-74, HD-73, HD-74).

A reinforced concrete bus loop was built in 1948 to accommodate the

trackless trolley (MA-14-32, MA-14-33).

EGLESTON STATION

Egleston Station, built in 1909, was the first station in which the plat-

forms, galleries and stair landings were designed for reinforced concrete

(HP-93).

A 350-foot platform was built to accommodate eight-car trains.

At

this time the other elevated station platforms were also enlarged for the same

purpose (HD-80).

The waiting room station on the first level was suspended from

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 46

the tfack support system and was reached by canti levered stai rways.

The des i gn

was a simplified, unembellished version of the original Longfellow station; a

rectangular structure, 44' x 22' with a half copper ribbed roof, windows,

pilasters and copper panels (HD-81, HP-94, HP-95).

More decorative emphasis was

given to the platform, which was positioned above the station on the second

1 eve 1.

It featured a ribbed copper canopy supported on iron columns and a

gallery with arched, sash windows and keystones, which the passenger entered via

a waiting room stairway (HP-96, HD-81).

The waiting room contained an alcove on

the west side, wooden benches, and an octagonal ticket office which was sheathed

in copper, finished in white ash, and detailed similarly to the original ticket

offices.

The floors of the waiting room, platform and gallery were of rein-

forced concrete (HD-82, HD-83).

In 1916, an enclosed footbridge with a patterned ceiling was constructed to

connect the original station to a surface car station (HD-84, HD-85).

GREEN STREET STATION

References to the original construction of Green Street are scarce.

However, there have been few major changes made to the exterior since it was

built in 1912.

Its design marks a clear departure from the Longfellow stations.

The east and west elevations were devoted almost totally to large, plate glass

windows. Above these were copper spandrels decorated with an unusual circle-

I appet mot if.

The window-spandrel composition was unified by a copper string-

course and paneled pilasters decorated with the circle-lappet motif.

Above the

stringcourse was a clerestory of smaller plate glass windows separated by

recessed pilasters (HD-89).

Most of the station's interior was sheathed in bead

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 47

ash, including the ticket office, which featured an ash grille in the ticket

wi ndow and a center fence wi th an ash handrai 1 (HD-87, HD-88).

In 1976, the

interior was completely rebuilt after it was badly damaged by a fire.

FOREST HILLS STATION

More is known about Forest Hills Station, including the name of its designer, Edmund March Wheelwright, an important local architect who also

designed Park Street Station.

Not only was this station widely publicized at

the time of its construction, but it has been vi rtually unaltered since its

erection in 1909.

Built as a terminus, it markedly differed in design and

construction from earlier stations.

Wheelwright intended it to harmonize with

the Arborway, part of the Boston park system designed by Frederick Law Olmsted.

Wheelwright was also clearly influenced by the stations of the Vienna Stadtbahn

designed by Otto Wagner in the 1890's, particularly the Gumpendorfer Strasse,

Josephstadter Strasse, and Alser Strasse stations on the Gurtel1inie. [3]

A massive structure of elegant proportions, it was constructed of rein-

forced concrete and embellished with copper details.

Trains approached the

station on a reinforced concrete viaduct which carried a double-track line

(HP-llO, HP-1l2).

High concrete balustrades minimized noise.

Support i ng the

viaduct was a single row of massive steel posts encased in concrete and sup-

ported on foundations 11'6" square and 12' deep.

The ma in frami ng was of deck

construction with steel plate cross and longitudinal girders.

All t i mbe r wo rk ,

including ties, guard rails and feeder box, was of hard pine.

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 48

The exterior of the station consisted of two concrete pavilions joined by a

long, double pl atform which was supported on a massive arcade of reinforced

(HP-113, HP-114) concrete piers.

Spanning the arches were two tiers of large,

double-hung glass and wood windows, the upper tier adjusted in shape to the cur-

vature of the arch.

The north pavilion was supported on two concrete posts and

a massive central pier.

Trains entered an arched portal, which was framed by

copper pil asters and keystone.

Recessed copper pilasters, panels, and crenela-

tions embellished the cornice (HD-93 through HD-96).

Inside the pavilion were

wait i ng rooms.

The track was open to the sky; the platforms on either side were

covered by copper canopies supported on posts, braces and diaphragm arches.

The

south pavilion was similar to the north pavilion except for its roof, which was

hipped instead of flat. [4]

Despite its scale and material, the overall effect

is light and graceful.

The station is admi rably adapted, not only to its site

but to the elevated system as a whole (HD-97, HD-98, HD-99).

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 49

NOTES Chapter 5

[1] En ineerin News (Supplement), March 31, 1898; Railroad Gazette (Vol XXX, no. 16 , April 22, 1898; Street Rai lway Journal (Vol. XIV, no. 9), Sept. 18, 1898, 501.

[2] BERy Co., 50 Years of Unified Transportation in Metropolitan Boston - 1938.

[3] Heinz Geertsegger and Max Peintner, Otto Wagner, 1848-1918 (New York: Rizzoli, 1979), pp. 47-78.

[4] In March 31, 1910 a large illuminated sign reading "Elevated" was installed over the South Portal. �

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 50

Chapter 6

Orange Line Structural Analysis and Description of the Elevated Structure

Section F-l thru F-7

1.

General Description

The Orange Line south elevated structure rises from the South

Portal of the Washington Street Tunnel, and then runs along

Washington Street to its terminus at Forest Hills.

The great

majority of the elevated structure consists of one of three variants of a "regular elevated railway deck type" [1]

structural bay constructed of sections built up of riveted

assemblages of rolled structural steel.

The rolled sub-

components are all standard sections with the exception of

the channels used as column flanges.

These were "speci ally

rolled ... with rounded corners, thus allowing abundance of wheel room and nothing to catch the hubs." [2]

HD-15

Generally the structural action of these bays is as follows.

Tracks carry the train loads through their supporting ties,

to the longitudinal trusses or girders.

These longitudinal

HP-21 HD-9

The

members frame into the top girders of transverse bents.

transverse girders frame into two columns, supported by

HD-26

concrete foundations, resting on solid rock, compacted earth

or pile clusters, depending on subsoil conditions. [3]

.

.

.

HD-14

HD-19

HD-15

Boston Elevated Railway Company HAER No. MA-14 Page 51

The longitudinal members occur in pairs, generally under the

two tracks, and the members of the pair are braced together

laterally by a system of transverse and/or diagonal members

in the horizontal plane.

They are fu rther stabi 1 i zed by a

system of "sway frames" cons i st i ng of crossed members runni ng

from the top chord of one truss or gi rder to the bottom chord

of its mate.

The longitudinal system is supported by an

expans i on pocket at the end of every thi rd span. Between these points rigid connections were used. Late r analysis revealed this to be one of the few des i gn faults in the

system.

The designers considered the longitudinal system to

act as a seri es of s impl e spans, but the ri gi d connections

made them approximate three span continuous beams.

(See

Anderson - Nichols & Co. report). [4J

There are three principal variations upon the "standard" bay

described above.

The first consists of both longitudinal and

transverse girders constructed from plate girders.

The

second consists of transverse girder bents and longitudinal

trusses.

The third consists of longitudinal trusses sup-

ported by "arched truss-bents ("type F")".

These three carry

the bulk of the elevated system.

There are many very mi nor

variations along the right-of-way to accomodate local con-

ditions and more substantial variations at a few special

stat ions.

The design drawing "Typical Elevations and Cross


Boston Elevated Railway Company HAER No. MA-14 Page 52

.

Sections" shows the typical support conditions and their

reasons for use which are principally a function of street

width.

Variations in the supporting structure occur to support the

additional functions required at stations and in response to

special structural requi rements.

Examples of the latter

include the special bent transverse girders composed of

hybrid truss and plate girders specialized additional 10ngi-

tudi na 1 braci ng. extra braei ng for unusually hi gh bents

longitudinal members with raised bottom chords longitudinal

members of varying depth and other atypical bracing.

.

For purposes of discussing specifics of the structure, the

right-of-way has been divided into a series of segments

starting in the north and proceeding southward; these are

defined by the section:

1.

South Portal to Tower "D" - Section "F-1"

2.

Tower "D", past Dover Station, to the Cathedral

- Section "F-2"

3.

The Cathedral to Thorndike Street (Bent #1068)

- Section "F-3"

4.

Thorndike Street thru Dudley Station to Guild

St reet - Sect i on "F -4"

5.

Guild Street to the Arborway - Section "F-5"

.

.

.

.

II.

HD-32 MA-14-2

HD-30

HD-31

Boston Elevated Railway Company HAER No. MA-14 Page 53

6.

Arborway to the Forest Hills Station and to the

storage ya rds.

Sections "F-6" and "F-?"

Oescription by Segments

(1 )

SECTION F-1

South Portal to Tower 0 (Bents #1215-#1200)

The initial segment of the elevated system, after it emerges

from the Washington Street Tunnel, and up to the point where it crosses the current location of the Massachusetts

Turnpike (formerly the B&A R.R.) does not run co1inear1y with

a street on grade.

It does, however, cross some minor

streets.

Since no street runs beneath the rail line, the

des i gners chose to support the system with fully braced fra-

mes, presumably for reasons of structu ra 1 effi ci ency.

The

bracing consists of OX's" running from the support gi rder at

one column to the base of its paired column.

Since the

transverse girders are relieved of their moment resisting

function, they are relatively shallow.

In addition, the

spans are short in this segment and the longitudinal members

are framed with girders.

(2) SECTION F-2 Tower D past the Cathedral (Bents #1215-#1143) �

.

.

.

HD-6 MA-14-3

MA-14-4

MA-14-5

HD-18 MA-14-7

Boston El evated Rai lway Company HAER No. MA-14 Page 54

After crossing the turnpike the structure joins Washington

St reet.

Th is is the 1 ocat i on of the ori gi na 1 "Wye" con-

necting the Roxbury Division with the Atlantic Avenue loop

(Section D).

Elements of the original framing remain along

with the ori gi nal switch tower and its supports.

Supplementary cross girders span between the columns of bents

1198 and 1199, forming secondary "transverse" bents, presu-

mably to support the old "Wye".

Remaining track support gir-

ders and trusses run perpendicular to the later alignment at

this point.

Approaching Dover Street solid girder bents were employed.

At the station the longitudinal trusses diverge although the

MA-14-12 tracks now run in a straight line. This appears to be a HP-28 HP-32 vestige of the station before its rebuilding in 1912. Upset

MA-14-10 girders were employed for track support at the station pro-

HD-24

MA-14-12 HP-33

viding headroom for the ticketing lobby below the station.

These are interesting in that no secondary framing was used,

but instead oversized ties span between the bottom flanges of

the girders to carry the rail loads. by additional longitudinal girders.

Platforms are carried

At the station, the

standard girder bents are fitted with cantilevered outriggers, supporting the platform structure. �

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 55

MA-14-13 Proceeding south from the station, Washington Street starts out quite narrow, and the bents span from sidewalk to

MA-14-14

MA-14-15 MA-14-16 MA-14-17 HD-22 HD-16 HD-23

HD-19

s i dewa 1 k. Shortly, the st reet wi dens a bit, and short spans replace the larger ones with columns coming down into the

street.

Some solid web and some trussed girders are used.

As Washington Street veers to the West, a substantial offset

occurs between the road alignment and the rail alignment

giving rise to very asymmetrical loading conditions.

These

are marked by a seri es of speci a 1 transverse bents some wi th

cant il evers and some wi th a hybri d truss - plate gi rder form of construction.

(3) SECTION F-3

The Cathedral to Thorndike Street (Bents #1143-#1068)

As Washington Street passes the Cathedral it starts to widen.

MA-14-18 The rail line supports become variants of the type "F" arch-

truss bent. The road and track alignments still differ,

inducing asymmetry in the supporting structure.

Co 1 umns are

frequently centered under one track, and a shallow trussed

girder is used in place of the full arch design.

Cantilevers

are employed as necessary to resolve the alignment

di fferences.

Beyond the Cathedral, Washington Street becomes wider and

regul ar.

The standard elegant type "F" arch-truss bent sup-

.

.

.

HD-20

Boston Elevated Railway Company HAER No. MA-14 Page 56

ports the system here.

Since columns are directly under the

track loads, the bents coul d be des i gned as 1 i ght, effi c i ent

forms although subsequent analysis has revealed deficiencies

in the lateral force resistance of the design.

(See

MA-14-20 HP22 Anderson-Nichols & Co. report). [4] Washington Street is HP23

quite level in this area, so that bents have a fairly

constant height.

Longitudinal members are trussed adding

to the light "airy" appearance of this portion of the line.

Engi neeri ng News observed, "The st ructure ... 1 eaves the

street much more open and unobstructed than does the usual

elevated railway, and the cross struts being arched present a handsome appearance as well." [5J

At Northampton Station, columns move to the ends of the

MA-14-24 bents, apparently to allow more horizontal clear space below

HD-17

HP-35 HP-39

HD-26

the tracks for surface vehicles.

An additional pair of

longitudinal trusses supports the platform areas between the

tracks.

In place of an arch, the transverse bents have a

constant depth with trusses used under the platform areas and

solid web girders under the station house.

(4) SECTION F-4

Thorndike Street to Guild Street (Bent #1068 - Guild Street)

Beyond the station, Washington Street continues regularly ti 11 it starts to aproach Dudley Street and the type "F" �

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 57

MA-14-26 bents continue through #1068.

After this, the tracks converge

and the street narrows and winds to the west.

Gi rder type

transverse bents with a three-hole style knee brace span

MA-14-42 the street to carry the longitudinal support members which

continue as trusses.

MA-14-28 Dudley Station was the original terminus of the system. The HP-41

line terminated in a loop of fairly tight radius, necessi-

HD-29

tating considerable additional lateral bracing and support.

Around the tight curve, non-prismatic transverse girders were

employed to create the necessary banking.

Even so, thi s

curve was the scene of a major derailment in 1910, shown in

photographs HP-59 and HP-60.

In addition, platform and station

supports, as well as support for the elevated surface line

loops complicate the appearance of the structure here.

In the areas of the station where "a minimum elevation of the

HD-25

tracks was desired, with the standard head-room below for

street cars and where it was necessary to prevent drippings,

a special through girder and solid floor construction was

employed." [6]

Supporting structure for three tracks wye off from the loop

MA-14-44

and continue south along Washington Street, forming part of

MA-14-45 the former Guild Street Yard.

The end of the yard segment

marks the end of the old style trussed longitudinal girders,

.

.

.

HP-53 HP-54

Boston Elevated Railway Company HAER No. MA-14 Page 58

and the end of the knee braces with three holes.

Two of the

MA-14-46 sion south of Dudley Station.

three yard tracks form the connecting link to the line exten-

HD-37 HP-83

HP-84

HP-85 HP-86

HD-38

HD-42

(5 )

SECTION F-5

Guild Street to the Arborway

Proceeding southward from Dudley Station, Washington Street

becomes narrower and passes through a much hillier area.

The

portion of the rail line which follows this section presents

a more util itarian aspect than did the original portion north

of Dudley Station.

In addition to solid web plate girder

transverse bents, longitudinal members are now structured as

sol id web members.

Knee braces have been redesigned with a

single hole, giving the whole structure a heavier appearance.

In certain areas, Washington Street dips markedly, and extra

high bents were designed to maintain the rail grade.

These

Bents, #920 through #932 and #962 through #969, have an

additional line of secondary bracing comprising a laced

"X" braci n9 runs bet-

MA-14-53 member spanning between the columns. HP-82

ween the transverse girder and the horizontal brace.

MA-14-47 Conversely, when Washington Street passes over a hill, very

short bents are used, such as number 947.

Where cross

streets occur at an area of short bents, longitudinal girders

have been redesigned with lower chords which arch upward to

.

.

.

MA-14-62

Boston Elevated Railway Company HAER No. MA-14 Page 59

gai n clearance.

The arch is usually composed of curved

segments at the span ends, while the center of the span ;s

still ususally straight.

Occasionally the bottom chord ;s

formed as a single long curve.

MA-14-50 Track and street do not always align in this section, but the

HP-88 HD-39

HP-94 HD-83 HD-82

MA-14-63

HP-98

HP-99

misalignment is not so great as in the northern portion.

Individual girders are adjusted to accomodate the varying

load position. usually by varying the size and location of flange cover plates and web stiffeners, but occasionally by

means of cantilevered outriggers.

Standard track support framing is employed at Egleston

Station, with the exception of one span where upset girders,

with floor beams and stringers, were used to gain headroom

over the passenger access ways.

This section of Washington Street from Egleston Station to

Green Street Station becomes very regular. and the track sup-

port structure is also very regular.

Typical bays occur

throughout the section, modified only by the occasional arch-

chord longitudinal gi rders as described above.

Green Street station was added to the system in 1912 after

the main design was complete.

As a result, the principal

MA-14-64 track support structure is unchanged through the station.

.

.

.

Boston Elevated Rai lway Company HAER No. MA-14 Page 60

MA-14-66 The ticketing area is hung as a gallery under the main longi-

MA-14-68 tudinal structure.

HD-41 HD-48

HP-I04 HP-I06

HD-44 HP-I09 HD-45 HD-46 HD-47

HP-114

(6) Green Street to Forest Hill Terminal

Proceeding South from Green Street, the typical framing con-

tinues until the Arborway is approached.

This is the final

terminal on the system and its design varies greatly from the

rest of the 1 ine.

The support structure is steel encased in

concrete, with single pylon-like columns carrying both longitudinal supports by means of a "Tee" shaped double can-

ti levered head.

Each pylon actually contains a cluster of

four steel columns, laced transversely.

The longitudinal

support is encased in concrete with a long arched soffit

spanning the center line between the columns.

Within the station, two-span transverse bents support longi-

tudinal girders.

The exterior columns of these bents are

encased in the concrete outer structure of the station.

The

longitudinal structure comprises both conventional deck-type

girders and upset through-type girders.

The maj or des i gn

MA-14-78 features of the station are more architecturally noteworthy rather than structurally exceptional.

South of the Forest Hills terminal, regular plate girder

MA-14-82 transverse bents carry the tracks along Washington Street a

.

.

.

III.

Boston Elevated Railway Company HAER No. MA-14 Page 61

short di stance, and begi n a gent 1 e grade to the exi st i ng

storage yards at the end of the system.

Subsequent Analysis

Between 1972 and 1973, the consulting firm of Anderson-

Nichols and Company, Inc. prepared an analysis of the state

of the Orange Line at that time.

Their report [4] gives a

detailed description of the corrosion and disrepair the ele-

vated structure had fallen into, after 30 or more years

without repainting.

While that discussion is not directly

rel evant to thi s descri pt ion, thei r ana lys is contains some

interesting information.

The original structure was very

conservatively designed, with a maximum design stress of 16 kips per square inch, and most areas they investigated deve-

loped stresses around 10 to 12 kips per square inch.

This

overdesign was responsible for the continued serviceability

of the structure, even though corrosion amounting to as much

as 30% loss of original metal had occurred.

Design inadequacies highlighted by sophisticated computerized

analyses were very few and were mentioned above.

Their

conclusions were that, corrosion notwithstanding, "the struc-

ture was found to presently be in an operable condition."

A

program of repairs and painting was proposed and carried out

which extended the useful life of the system into the 1980s.

'.~

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 62

NOTES Chapter 6

[1] Engi neeri ng News, Vol. XLI, No. 19, May 11, 1899, p.304 [2] Engi neeri ng News, Vol. XLI I I, No. 11, Ma rch 15, 1900, p.180 [3] Engi neeri ng News, Vol. XLI, No. 19, May 11, 1899, p.304

[4] Structural Investigation and Analysis, Elevated Structure and Stations, MBTA Orange Line. February 1973. Consultants: Anderson-Nichols and Company, Inc.

[5] Engineering News, Vol. XLIII, No. II, March 15, 1900, p.180

[6] Engineering News, Vol. XLI, No. 19, May II, 1899, p.304

-'i-~"

Boston Elevated Railway Company HAER No. MA-14 Page 63

.

BIBLIOGRAPHY

Blodgett, Geoffrey. The Gentle Reformers: Massachusetts Democrats in Cleveland Era. Cambridge, Massachusetts: Harvard University Press, 1966.

Boston: City Planning Board. A Compendium of Reports and Studies Relating to the Commerce and Industries of Boston. Boston: Boston Printing Department 1924.

Boston Elevated Railway Company. Fift~ Years of Unified Transportation in Metropolitan Boston. Boston, 193 .

Reference List of Literature on Electric Railway Transportation in Boston as of February, 1927. Boston: Boston Elevated Railway Library, 1927.

Statutes, Surface Railway Leases, Contracts, etc., 1887-1916. Boston, 19i6.

Urban and Electric Railways: A Selected Reference List of General Literature. Boston: Boston Elevated Railway Library, 1930.

.

Boston Local Transit Companies. Annual reports, financial and other documents of the Boston Elevated Railway Company, the West End Street Railway Company and Boston horse railways. Corporate Records Division of Baker Library at Harvard Business School.

Scrapbooks and miscellaneous data. Library.

Boston Street Railway Association: The Boston Transit Album Bulletins No. Fourteen and No. Seventeen - Bradley Clarke.

Massachusetts Bay Transit Authority

Boston Transit Commission.

Annual Reports, 1895-1918.

Cheape, Charles W. Press, 1980.

Cudahy, Brian J. Change at Park Street Under: The Story of Boston's Subways. Brattleboro, Vermont: S. Greene Press, 1972.

Moving the Masses.

Cambridge, Mass:

Harvard Uni versity

Geretsegger, Heinz and Max Peintner, Otto Wagner, 1848-1918 (New York: 1979).

Ri zzol i,

McKay, John P. Tramways and Trolleys: The Rise of Urban Mass Transit in Europe. Princeton, New Jersey: Princeton University Press. 1976.

Mason, Alpheus T. Brandeis:

A Free Man's Life.

New York:

Viking Press, 1956

.

._>;....;..,.,~%.

.

.

.

Boston Elevated Railway Company HAER No. MA-14 Page 64

Mason, Edward S. The Street Railway in Massachusetts: The Rise and Decline of an Industry. Cambridge, Massachusetts: Harvard University Press, 1932.

Massachusetts. Board of Railroad Commissioners.

Annual Reports, 1880-1913.

Massachusetts General Court: Committees. Boston Elevated Railways, 1925. Reference List of Literature Pertaining to the Transportation System of Metropolitan Boston, 1910-1924. Boston, 1925.

Rapid Transit Commission. Report of the Rapid Transit Commission to the Massachusetts Legislature, April 5, 1892.

Charles E. Powers' collection of clippings in the Massachusetts Statehouse Library about elevated railroads in Boston and New York. 3 vols. 1878-82.

Meigs, Joe Vincent. The Meigs Elevated Railway System.

Boston, 1887.

Middleton, William D. The Time of the Trolley. Publishing Company, 1967.

Milwaukee, Wisconsin:

Kalmbach

Miller, John A. Fares, Please!

New York:

Dover Publications, 1960.

Peabody, Robert Swain, Holiday Study of Cities and Ports (Boston: Soci ety of Architects, 1908).

Boston

Pinanski, Abraham Edward. The Street Railway System of Metropolitan Boston New York: McGraw Publishing Company, 1908. .

Reed, Robert C. The New York Elevated. 1978.

New York:

A.S. Barnes and Company,

Reeves, William F. The First Elevated Railroads in Manhattan and the Bronx, the City of New York. New York: New York Historical Society, 1936.

Sprague, Frank J. "The Electric Railway," Century Magazine, 70 (July-August 1905), 434-451, 512-526.

Street Railway Journal, 1884-1907. Street Railway Review, 1891-1906.

Transportation Bulletin No. 82 Jan. 1975: ~

Warehousepoint Trolley Museum. State Street Railway.

Warner, Sam B. Streetcar Suburbs: The Process of Growth in Boston. Cambridge, Massachusetts: Harvard University Press, 1962.

1870-1900.

The Urban Wilderness: Harper and Row, 1972.

A History of the American City.

New York:

'MiJiii):'dy,

.

.

'.

Boston Elevated Railway Company HAER No. MA-14 Page 65 Up , i ..

Whitehill, Walter M. Boston: A Topographical History. Cambridge, Massachusetts: Harvard University Press, 1963.

/ .'

"

/3-

Zaitzevsky, Cynthia, Frederick Law Olmsted and the Boston Park System Cambridge, Massachusetts: Harvard Unversity Press, 1982.

Zaitzevsky, Cynthia, Nikita Zaitzevsky and Calvin Opitz, "Four Bridges on the Provi dence Oi vi s i on of the New Haven Railroad," HAER Report, 1980.

"