Page:EB1911 - Volume 17.djvu/260

From Wikisource
Jump to navigation Jump to search
This page has been proofread, but needs to be validated.
  
MACHINE-GUN
245


at (46) by a pivot to a long link with a cross head, termed the retracting connexion (45). This link extends from a point close to the figures (44), where the arms of the cross head bear against the ends of two long spiral retracting springs, (37) and (38), contained in two tubes, (39) and (40), which are slotted for a few inches of their length to allow the cross head to follow up and compress the springs. (Only (38) and (40) are shown, (37) and (39) lying in the same plane of projection.)

When the gun fires, and the bullet has passed the port, the gases drive the piston (35) and gas lever (29) downwards, and the momentum imparted causes them to swing back round the pivot (36), as shown by the dotted circle. The gas lever is brought up now by the bottom plate (91); and the retracting springs, compressed by the cross head of the long link (45) owing to the forward motion of the short arm of the gas lever, react and drive the gas lever into its forward position again.

Figs. 17 and 18.—Colt Automatic Gun Mechanism.

The rotary movement of the gas lever is converted into a reciprocating movement of the slide (86) by means of the gas lever connexion rod (31) pivoted at (32) to the gas lever, and at (87) to the slide.

The slide (86) is a nearly flat bar, travelling in guides in the receiver, extending from (14) to (87). It is slotted completely through longitudinally for nearly the whole of its length, this slot affording an opening through which work the cartridge extractor (82) and carrier (21). At its rear end it engages by means of a pin (14) in a cam slot (97) in the bottom rib of the bolt (13), and at (83) it bears the pivot of the cartridge extractor (82). Its rear end is enlarged below to form a cam lug (98), and on its right side are two projections (95) and (96), which work the feed lever (66).

Fig. 19.—Colt Gun mounted.

The feed wheel (61), over which passes the belt containing the cartridges, is actuated by a pawl “step-by-step” gear by means of the feed lever (66).

The carrier (21) is a long trip lever pivoted at (22), and provided with a spring dog (23) pivoted at (24).

The bolt (13) is a cylinder with a guide rib extending from its under surface. It is actuated by the slide by means of the pin (14) and cam slot (97) as already stated, and is bored through to take the striker or firing pin (18). The rear end of the latter projects slightly beyond the rear face of the bolt, being retained in this position by the spring (19). When this projecting end is pushed into the bolt, the point protrudes from the front of the bolt and fires the cartridge. The bolt, when the breech is locked, is held firm by two recoil blocks on the receiver (not shown), as is explained later. At the front of the bolt is an extractor (15) with a spring claw for extracting the fired case. (This is of course quite distinct from the cartridge extractor (82).) Ejection is effected by means of an ejector projecting into the path of the fired case.

The firing of the gun is performed by the cylindrical hammer (6) hollowed out in rear to contain the mainspring (7). When pushed back and cocked as shown in fig. 18, it is held during a portion of the operations of the mechanism by two detents working independently of each other—the sear (10) and the nose of the trigger (8). The former is automatically released by a trip lever (not shown) as soon as the breech is locked, leaving the hammer held by the trigger only. This is the position shown in fig. 18. The necessity for the two detents is explained later.

The hammer, when cocked, can also be permanently locked by the handle lock (2) actuated by a thumb-piece on the outside of the receiver. The air compressed in rear of the hammer, as the latter is driven back, passes through the tube (99) to the breech; and a puff of air is therefore blown through the barrel after every shot, clearing out fouling and unconsumed powder, and assisting to an appreciable extent to keep down the temperature of the barrel.

Taking the position shown in fig. 18, the hammer is only held back by the trigger nose, the sear (10) having been released as stated above. A belt of cartridges (not shown) has been placed on the feed-wheel, and the cartridge next to be used after the one (not shown) now in the breech has its rim (or base with rimless cartridges) just above the hook on the extractor (82). If now the trigger be pulled, the hammer flies forwards, strikes the protruding end of the firing pin, and the cartridge fires; the gases cause the gas lever to swing round and drive back the slide. The pin (14) working in the cam groove (97) causes the rear of the bolt to rise and clear itself from the recoil blocks (not shown) on the receiver, and then to move rearwards horizontally, driving the hammer back until the latter is caught and held by the sear and trigger. In the meantime the extractor (82) has pulled a cartridge from the belt, and, assisted by two spring cartridge guides (80 and 81), of which only (80) is shown, deposits it on the carrier (21); the projection (95) strikes the feed-lever (66), and moves the feed mechanism so as to prepare to revolve the feed-wheel and place a fresh cartridge ready for the next round; and as the slide completes its travel backwards, the cam (98) strikes the dog (23) and slightly depresses it (the spring (25) yielding), the