A Complete Course in Dressmaking/Lesson 3/Patterns
Making a Brassiere Pattern: In the previous lesson you learned how to use a block
Fig (27) An easy-to-fit brassiere design
shirtwaist pattern to make an apron. You can use your same block waist pattern to make a brassiere like the one shown in Fig. 27, too.
Lay your blouse pattern around the outside. Then remove the original pattern. Use the outlines marked as diagram. (See Figs.28 and 29.)
At a point about eight inches down from the neck in the front mark a point as D and draw a line from this point to the bottom of the armhole as the line DE. This line should correspond to an imaginary line at the fullest part of the bust on the person. To fix point D in exactly the right place, measure on the person from the base of the neck in the front to the fullest point of the bust, measuring at the center front. In the back square a line from the center back to the bottom of the armhole, line DC, Fig. 29.
Fig. (28) Diagram for front of brassiere
A brassiere ought to fit tighter than a blouse. Pass the tape around the form as if taking the bust measure. See Lesson I. Draw it as tightly as you want the brassiere to fit. Half this amount will give you the size your pattern ought to be from the center front to the underarm and across the back. If your pattern measures more, take off the extra amount at the underarm seam. Suppose your waist pattern measures eighteen inches on the half across line DE, Fig. 28, and line DC, Fig. 29. This would make the finished garment thirty-six inches. If you want the finished brassiere to measure thirty-four inches, half the brassiere pattern ought to
Fig. (29) Diagram for back of brassiere measure seventeen inches and there will be one inch to take off of half the pattern. Mark a point on the line DE, Fig. 28, one-half inch in from the underarm seam. Also measure in a half inch from the center of the armhole and reslope the armhole as the chest width ought to also be narrower than on a blouse pattern. (See line JE, Fig. 28, and line HD, Fig. 29.)
The brassiere will stay on the shoulders better if the line is thrown in from the top of the shoulder as point J, Fig. 28. Mark the curve for the low neck as desired, lines GKH on Fig. 28 and Fig. 29.
Since a brassiere fits tightly, you can take out an inch of the fullness at the lower edge at the front edge. To do this mark point C one inch from the front line AB and draw a new line CD. Line CDG will be the center-front edge of the brassiere.
You can also take out an inch at the underarm seam and draw a new line as FE Fig. 28, and ED, Fig. 29.
Decide on how many seams you want in the brassiere and mark them roughly on the diagrams.
Measure from point C to F on Fig. 28 and from E to B, Fig. 29. Then take the waist measure of the person tightly. Subtract half the waist measure from the size of half the pattern at the lower edge and it will give you the amount that you must take out in darts to make it tight fitting. For instance, if half the pattern measures fifteen inches and half the person’s waist measure is twelve inches there will be three inches to take out in darts.
Mark points at the lower edge of the pattern either side of each seam to take out the extra goods. From L to M, from R to S, Fig. 28, and from P to R, from M to N and from K to J, Fig. 29, ought to equal the amount you want to take out in darts. In the case mentioned above, it would be three inches.
On the front, run lines from the dart markings at the bottom to the seam line where it touches the bust line DE. On the back, run the lines from the dart marks to the seam lines where they touch line DC. The darts must not be extended higher than the line DE, Fig. 28, or the line DC, Fig. 29, for they must not extend above the fullest part of the bust or the fullest part of the back.
The number of seams can be varied and their spacing varied to suit your taste.
It is well to mark the neck and armhole lines in the front first. Then use this as a guide in marking the corresponding lines in the back. Point H, Fig. 29, must be the same distance from the outside of the armhole as point J is in Fig. 28. Also point F, Fig. 29, must be the same distance from the neck that point H is in Fig. 28.
Test the curve at the neck and armhole by tracing these portions of the front and back patterns. Cut them out and bring them together at the shoulder. The curves should be even and continuous. If they jog, fill them, if they point out, cut them off.
Make a comparison of the underarm seams and lower edge curve in the same way. See
Fig. (30) True up the lower edge
Fig. 30. This illustrates a case where the front needed trimming off a little.
As the front and back edges of the darts must sew together, they must measure exactly the same. As the seams are just one line above the bust line, DE, Fig. 28, and line DC, Fig. 29, test the length of the sides of the darts below these lines. TL should measure exactly the same as TM, Fig. 28. The best way of truing up the darts is to measure TL and then mark this same distance on TM. If TM is shorter or longer reslope the lower edge from M to R, starting from the new point marked on line TM. True up the other darts in the same way.
The diagram often comes in handy for reference, so do not cut these apart for a pattern. Trace off your pattern. Put a piece of paper under the diagram and trace the front piece, tracing crosswise at the bust line. Remove the under piece of paper and mark the seams allowance beyond the edges and a hem at the center front. Cut out the pattern and notch it at the bust line. Trace and cut out the other pieces in the same way.
Cutting a Brassiere: Use a material of firm texture but not bulky. Linen, allover embroidered cotton and twilled muslin are practical goods.
Fig. 31 shows the pieces of a brassiere such as the one illustrated in Fig. 27 laid on the material folded double. Note that the centerback section is laid on the fold of the goods. The other sections are placed so that the front edges come as nearly as possible on the straight thread of the goods.
When the seams are joined, this throws a straight and a bias edge together. The straight edge acts as a stay for the bias edge. The exact placing of the pieces on the goods may vary according to the width of the goods and the size of the pieces. The best plan is to lay the back on first with the center-back edge on the fold of the goods and then fit in the other pieces. Usually there is no up nor down to brassiere fabrics, so the pieces may be reversed if it will save goods. The Fig. 32
Fig. (32) Underwear materials haven't an up and down so you can reverse ‘pieces of the pattern
shows two pieces reversed: that is, the top of one piece points in one direction while the top of the other piece points in the opposite direction.
After the pieces are arranged to the best possible advantage, weigh down each piece, mark around it with tailors’ wax or chalk and cut with heavy shears as described in Lesson II. After cutting any garment iron out each piece. Do not attempt to sew wrinkled pieces.
Making the Brassiere: Finish the front closing first. Turn the hems on the two front pieces and stitch as shown in Fig. 33.
The easiest way of finishing the closing is to apply tape that has hooks and eyes fastened to it. You can buy this tape at any department or notion store.
Fig. (33) Hemming the front edge
Pin the tape in position along the back edge of the hem and stitch as shown in Fig. 34. If for any reason you cannot secure the tape, sew on hooks and eyes along the edge of the closing, placing them close together.
Fig. (34) You can buy tape with hooks and eyes attached for finishing the closing
Baste the brassiere together, taking the exact seam allowance and try it on before stitching the seams. Baste as shown in Fig. 35 with the raw edges extending on the wrong side of the garment. Try on the brassiere. If it is loose at any point, take up the seams until it sets smoothly.
Before ripping the bastings, mark the exact stitching line with a tracing wheel.
Fig. (36) Keep the notches together in stitching the seams
![](http://upload.wikimedia.org/wikipedia/commons/thumb/c/cc/A_complete_course_in_dressmaking%2C_%28Vol._3%2C_Underwear%29_%28IA_completecoursein03cono%29_%28page_30c_crop%29.jpg/200px-A_complete_course_in_dressmaking%2C_%28Vol._3%2C_Underwear%29_%28IA_completecoursein03cono%29_%28page_30c_crop%29.jpg)
In joining the first seam, stitch as shown in Fig. 36. Trim off one edge to within oneeighth of an inch of the stitching, turn under the wide side, fold it over and stitch as shown in Fig. 37.
Fig. (38) The position of the needle in making the buttonhole
Reinforce the seam with tape three-eighths of an inch wide. Cut the tape the length of the seam and cut and work a buttonhole one-quarter of an inch below where top of the bone will come. The Fig. 38 shows the position of the needle in working a buttonhole. Stitch the tape over the seam as shown in Fig. 39. Insert featherboning the
Reinforce the underarm with shield-shaped pieces of material. Turn under the edges and bottom of the shield-shaped piece, and press it, baste it to the wrong side of the brassiere at the underarm and stitch as shown in Fig. 40.
Close the shoulder seams and tape these
![]() fasten to the corsets |
![]() to the neck |
seams as the other seams were closed and taped.
Make a loop of tape and work an eyelet with buttonhole stitches as in Fig. 41. Join this to the bottom of the brassiere at the front. It can be hooked over the corset to hold the brassiere down.
The best finish for the neck, armholes and lower edge of the brassiere is a narrow embroidered edging. Lay the edging on the right side of the brassiere along the edge and stitch a seam’s width from the edge. (See Fig. 42.)
Cut off the raw edges of the brassiere close to the stitching. (See Fig. 43.) Fold under the raw edge of the embroidered edging and stitch it flat to the wrong side of the brassiere as shown in Fig. 44
Garter Supports for Your Brassiere:
Perhaps you want your brassiere to take the place of a corset. Then add garter supports in the front, as shown in Fig. 45 All you will need to do is trace off the two front pieces and use these as a foundation. Thumb tack them to another piece of paper, as shown in Fig. 46. Draw the outline for the garter support below as indicated by the dotted lines. In tracing off the new pattern, mark around the upper and side edges of the front piece and the garter support. Cut the garter support in one with the front piece.
![]() |
![]() |
Making a Different Style Brassiere Pattern: There are innumerable ways in which you can vary the seams of the brassiere, once you have your foundation tight fitting pattern. If you want the lower part of the brassiere in one piece, place the pattern pieces as shown in Fig. 47. This shows the three pieces for the front placed with the sides of the darts together. Draw a line where you want the lower edge of the new upper section to come, as the dotted line on the Fig. 47. In tracing the new lower front pattern, run the tracer along the dotted line to the dart at the arm-hole, then run it around the outside of the lower part. Allow seams in cutting it out.
Fig. (48) The pattern pieces put together to form one-piece yoke
Place another piece of paper under the diagram and trace the upper part of the two front pieces, running the tracing wheel across the dotted line and around the upper edges. Remove the paper and cut out these two pieces. Place them on another piece of paper, as shown in Fig. 48, bringing them together. Mark around the outer edges and allow seams. When you cut out the new piece you will have a one-piece circular yoke pattern.
When made up the brassiere will look like the one shown in Fig. 49.
The back can be cut in one piece with a yoke in the same way.
Making a Pattern for an Envelope Chemise: The regulation envelope chemise shown in Fig. 50 can be copied easily with your block waist pattern as a foundation.
Lay your foundation pattern on another piece of paper and trace around the outside. Remove the patterns and use the traced outline as diagrams. (See Figs. 51 and 52.) Decide how low you want the neck of the chemise in the front and mark a point at this depth On the Center front line of the waist. A waist has more fullness in the front than is needed in a chemise, so mark a point one inch back from the front edge on the lower edge of the waist as point C. Draw a line from point C to B and continue it below the lower edge of the waist. This will be the center-front line of the chemise.
Decide how long you want the chemise. Measure on the person from the base of the neck down the desired depth. Note what the measurement is in inches.
To determine the correct length of back, you must find out how far from the floor the chemise will hang in the front. To do this fasten a pin in the garment which the person is wearing at the depth you want the chemise to come in the front. Measure from the floor up to this pin. Suppose this measure was eighteen inches. Measure the same amount up from the floor in the center back and fasten a pin in the garment at this point. When you have determined the distance up from the floor in the back, measure from the base of the neck in the back to the pin and note what the measurement is in inches.
Measure on the diagram from the neck edge in the front down the center-front line the length of front measured on the person and mark point G. In the back, measure the length of back along the center-back line and mark point C.
Draw a line at right angles to the center-front line, starting at point G. See line GH, Fig. 51. Draw a line from the center-back line at right angles to it as line CD.
Continue the lines of the underarm seams in the front and back. To have a good run at the lower edge, the line must curve. In Fig. 51, measure up on line JH one and one-half inches and mark point I. Curve a line from I to the lower edge. In Fig. 52, measure back the same distance on line FD and mark point E. Curve a line from E to the lower edge.
To prevent the shoulder straps from slipping off the shoulder, bring them well in on the shoulders in the diagrams. Mark the new armhole line and neck line on the diagrams. Mark these lines on the front first and then mark the corresponding lines on the back. Point G on the back must be the same distance from the armhole that point F is from the armhole in the front. Also, point H on the back must be the same distance from the neck edge that point E is from the neck edge in the front.
Continue the center-back line to form the strap that goes between the legs. To determine how long to make the strap, pass a cord from the base of the neck in the back on the person being measured between the legs to the base of the neck in the front. Let it hang sufficiently loose so that the person can bend over and sit down comfortably. Note the measurement in inches. Now measure on the diagrams from the neck edge in the front to the lower edge and from the neck edge in the back to the lower edge. Add these two measurements and subtract the total from the amount the cord measured. This gives you the amount to make the strap from point C to B. Curve the upper part of the strap to blend into the lower edge line.
Lay a piece of paper underneath the front diagram and trace around the outer edges of the chemise pattern.
In cutting out the pattern, allow seams at the neck, armhole, shoulder, underarm and lower edges. The center-front is laid on the fold when the garment is cut out, so does not
Fig. (53) A smooth run at the lower edge. require a seam. Trace the back pattern in the same way. The center-back is also laid on a fold.
Test the run of the line at the lower edge by bringing the underarm seams of the pattern together. Fig. 53 shows a pattern that has a perfect run at the lower edge. The garment made from this pattern will hang evenly. Fig. 54 shows a pattern that needs filling at the underarm seam, as indicated by the dotted line. Fig. 55 shows a pattern that needs cutting off to give the lower edge a smooth line.
If you want to add fullness to the front of the chemise:—Mark lines parallel to the center-front and about one inch apart as shown in Fig. 56. Also number the pieces.
Cut the pattern apart along these lines. Draw a line on another piece of paper and thumb tack the first piece along this line. Draw a line at right angles to the back edge of the first piece starting at the upper edge. Place the second piece one-half inch beyond the first piece with the front upper edge on the line that was squared out from the first piece. Place the third piece one-half inch beyond the second piece with the front upper edge in line with the back upper edge of the second piece. Then place the fourth piece one-half inch beyond the third piece with the front upper edge in line with the back upper edge of the third piece. Trace around the outer edge of these pieces, re-slanting the upper edge as indicated by the dotted line in Fig. 57. When you remove the pieces you will have a pattern for a new front with fullness.
Fig. (56) To add fullness mark the chemise pattern in sections
You can vary the amount of fullness added by spreading the pieces more or less. This gives a front with fullness added all the way through.
If you want to add fullness only at the top, spread the pieces at the top only. Fig. 58 will give you the idea. In tracing around the pieces, reslope the lower edge so it will not jog up in the front.
Fullness can be added through the lower part only by keeping the pieces together at the top and spreading the bottoms.
Fullness can be added to any garment if you follow this same plan.
Fig. (57) Spreading the pattern to add fullness
Fig. (58) Putting in fullness at the top of the chemise
Cutting a Chemise: The layout, Fig. 59, shows the material folded double lengthwise. Note that the center-front and the center-back edges are laid on the fold.
If it happens that the pattern does not cover half the material in width, do not fold the goods in the exact center but fold only an amount equal to the width of the pattern as in Diagram 60. This throws practically all the material left into one piece at the side, which probably can be used in making some other piece of underwear.
If the material were folded in the exact center and the pattern did not cover the entire width, the material left would be in two long narrow strips, a shape which seldom works to good advantage in making any other garments.
After the chemise pattern is properly laid on the goods, mark around it and cut as described in Lesson II.
Fig. (61) French seam the shoulders of the chemiseMaking the Chemise: Close the shoulder seams first. (See Fig. 61.) French seams give the best finish.
Just as soon as the shoulder seams are closed run a thread around the neck, a seam's width in from the edge, draw the thread up a trifle and secure the end with several over-and-overFig. (62) In thin materials, a French seam gives the neatest finish at the underarm stitches. As the neck edges are bias at the sides, the neck of any garment is almost sure to stretch unless the stay thread is run around it.
Make French seams at the underarm. (See Fig. 62.) Before finishing the lower edge, stitch an oblong facing to the lower portion of the chemise at the center-front. (See Fig. 63.) This is the place where the tab buttons when the garment is finished. Finish the neck, armholes and lower edge with lace edging. Put it on as described in the first part of the lesson.
Turn a hem at the end of the tab. ![](http://upload.wikimedia.org/wikipedia/commons/thumb/f/f7/A_complete_course_in_dressmaking%2C_%28Vol._3%2C_Underwear%29_%28IA_completecoursein03cono%29_%28page_49a_crop%29.jpg/290px-A_complete_course_in_dressmaking%2C_%28Vol._3%2C_Underwear%29_%28IA_completecoursein03cono%29_%28page_49a_crop%29.jpg)
Fig. (63) Face the front to give a foundation for the buttonholes
(See Fig. 64.) Sew buttons to the tab and work buttonholes in the lower edge of the front piece as shown in Fig. 65.
The made-up garment will look as Fig. 66.
Fig, (66) Lace edging makes a pretty finish for a chemise
Fig, (65) The closing completed
Fig. (67) There is nothing nicer for crepe de chine than a set-in design Making a Pattern for a Step-in Chemise: With a plain chemise pattern to work on, you can change the design as much as you like. If it's a step-in style that you want to copy, as shown in Fig. 67, it means cutting off the top and reshaping the lower edge.
Lay your foundation chemise pattern on another piece of paper and trace around it. (See Fig. 68.) Draw lines at right angles to the center front and center back that touch the bottom of the armholes. This gives you the new upper lines.
If you want to shape the chemise a little at the back, draw a line at right angle to the center-back line at the normal waistline. Measure in on this line three-quarters of an inch and mark point F. Curve a
Fig. (68) Diagram for step-in chemise
line from the upper to the lower edge, touching this point. This gives you a new centerback line. In cutting out your pattern add a seam allowance beyond this edge, as a curved edge must have a seam and cannot be cut on the fold of the goods.
Extend the center-front and center-back lines below the lower edge of the chemise. Measure one-half the length of the strap of the envelope chemise beyond the lower edge at the front and back. Curve the straps to blend in to the lower edge of the chemise. In tracing the new pattern, allow seams at all points except the center-front edge. The center-front edge will be laid on the fold. Allow a hem beyond the upper edges.
Making a Step-in Chemise: Close the underarm seams first. French seams will give the neatest finish. Leave them open for a space of six inches at the lower edge.
Also make a French seam in joining the strap at the lower edge.
Before hemming the top of the chemise, make and finish a quarter-inch slash at the center-front one-half inch downFig. (69) Mark the slash on the goods from the top. This affords a place for inserting the ribbon in the hem.
The easiest way of finishing this slash is to face it. Mark the slash as shown in Fig. 69. Cover this mark with a facing piece, cut to
Fig. (70) Facing the slash
Fig. (71) A cardboard guide will help to keep the edge turned evenly
extend one-half inch beyond the mark at all points. Indicate the place of the slash on this facing piece and stitch around the mark as shown in Fig. 70. Cut the slash and turn the facing piece through the slash onto the wrong side. Press the facing and stitch around the opening again, or catch the facing to the outside by hand.
After this is done, turn a one-half inch hem at the top. A piece of cardboard notched makes an excellent guide for turning the hem. (See Fig. 71.)
Press the hem in place and stitch around the top of the chemise, running the stitching about three-eighths of an inch from the top. If you want a little nicer finish, fell the hem in place.
Insert a narrow ribbon in the eye of a bodkin and run it in the hem, leaving ends long enough to tie in a bow in the front.
Finish the lower edges and the sides of the leg with a shaped facing. The easiest way to cut the facing is to measure back on the pattern at the edges one and one-half inches, measuring along with a ruler and marking points about one inch apart. Draw a line between these points, lay the pattern on another piece of paper and trace a pattern for the facing.
Lay the facing on the right side of the goods along the edge with the right side of the facing next to the right side of the goods. Stitch parallel to the edge and turn the facing onto the wrong side of the goods. Turn under the raw edge of the facing and stitch it in place.
Making a Pattern for a Chemise with Circular Flounces: Even a chemise with flounces can be worked out with a plain chemise pattern.
To copy the style shown in Fig. 72, lay the plain chemise on another piece of paper and mark around the edges. As in the case of the step-in chemise, use these traced outlines for diagrams.
If desired, curve the back seam as in the step-in chemise. (See Figs. 73 and 74.) Mark the new upper lines.
Fig. (72) The chemise with circular flounces is also a step-in
Decide how deep you want the flounces at the side seams and mark points C. From points C curve lines to the lower front and back edges, lines AC.
Between the legs the ruffles need be only about half as deep as at the underarm seam. Make the line AE about half the depth of CD. Slant it to form the crotch. Draw the lower edge of the ruffle from E to D.
Put another piece of paper under the diagrams and trace off the ruffle patterns. If these ruffle patterns were used the ruffle would be very narrow at the bottom. You will need to spread it and put in fullness.
Draw lines across the ruffle patterns as
![]() |
![]() |
shown in Fig. 75. Cut the patterns along these lines and spread the pieces at the bottom as shown in Fig. 76. Reslope the lower edge to give a smooth curve. Allow seams in cutting the new pattern. Trace the upper portions from the diagram, Figs. 73 and 74.
Making the Chemise with Circular Flounces: Close the underleg seams in the two ruffles. French seams will serve best here. Also close the underarm seams giving them the French seam finish.
Then join the ruffles to the lower edge. Lay the ruffle on the chemise with the right side of the ruffle next to the right side of the chemise and the upper edge of the ruffle even with the lower edge of the chemise. Stitch along the lower edge. Turn the ruffle into its finished position and from the right side of the garment stitch along the joining again.
Hem the lower edge of the ruffles and finish the top of the chemise with a hem, as described in making the step-in chemise.
A Ribbon Camisole: One of the undergarments that is easiest to make is a ribbon camisole that slips on over the head. The Fig. 77 shows a garment of this type.
Twelve-inch ribbon is wide enough to make it. When the ends of the ribbon are joined, the camisole ought to be large enough to pass comfortably over the shoulders. The best place to make the seam is at the left underarm. A French seam will give the neatest finish.
Fold the camisole as shown in Fig. 78. Note that the space is longer from the under
Fig. (77) A ribbon camisole is easy to make
arm seam to the center-front than it is from the underarm seam to the center-back. For the average figure, there ought to be about two inches more on the half in the front than in the back, but this varies according to a person's width of chest and width of back.
Fig. (78) The lower edge of the camisole needs shaping
To fit well, the camisole must be shorter in the back from top to bottom than it is in the front. Cut off the bottom, starting at a point one and one-half inches above the lower edge at the center-back, and running to nothing either side of the front.
Finish the top of the camisole the same as the top of the step-in chemise is finished.
The lower edge of the camisole is best finished with a bias casing of lawn or silk. Cut a bias strip one and one-quarter inches wide for this purpose. Cut off one end of the bias strip straight across and turn a seam on this end. Lay the bias strip along the lower edge of the camisole on the right side, starting at the seam. When you have pinned it in place all the way
Fig. (79) Finish the lower edge with a fold of goods around, cut off any remaining bias, leaving a seam's width to turn back. (See Fig. 79.)
Stitch around the lower edge of the camisole, running the stitching three-eighths of an inch from the edge. (Three-eighths of an inch is a regulation seam's width.)
Cut off the raw edges to within one-eighth of an inch of the stitching and turn the bias strip onto the wrong side of the camisole. Fold under the free edge of the bias and stitch
![]() |
![]() |
as shown in Fig. 80 or fell the upper edge of the bias by hand.
Insert one-quarter inch wide elastic in the casing thus formed. Cut the elastic to fit the waistline snugly, allowing one inch for lap. Run in the elastic with a bodkin. After the elastic is run in the casing, lap the ends of the elastic and fasten securely with over-and-over stitches. (See Fig. 81.)
Try on the camisole to determine the proper length for the shoulder straps and where to place them. The straps should extend to the bottom of the hem at the top of the camisole and be sufficiently long to turn a seam off at the ends of each strap. One-inch-wide ribbon makes comfortable straps. After the straps are pinned in place, fold the camisole to make sure the position of the straps matches on both sides. (See Fig 82.) The Fig. 83 shows one end of the strap stitched to the camisole. If you are finishing the camisole by hand sew on the straps with running stitches.
Fig. (82) Adjusting the ribbon shoulder straps
Fig. (83) Sewing on the shoulder straps
Making a Pattern for Circular Drawers: (See Fig. 84.) Draw the line AB the approximate width you want one drawer leg when finished. Draw lines AC and BD parallel to it and three inches deeper than you want
Fig. (84) Diagram for circular drawers
the length of the drawers at the sides.
Mark point E halfway between A and B and point F halfway between C and D and draw a line. This gives you the side of the drawers. Measure one-quarter inch less than one-quarter of the waist measure in front of point E and mark point G. Also measure one-quarter inch less than one-quarter of the waist measure in back of point E and mark point L. Measure down three inches on line EF and mark a point. Swing a curved line from G to L touching this point. Measure along the curved line and see if it is not exactly the waist measure. You see, a curved line is always longer than a straight line between the same two points. If it is a trifle short, spread points G and L until it is exactly the right measure.
Measure on the person from the center-front at the waistline between the legs to the center-back at the waistline. Let the tape measure or cord hang loosely enough so that the person can bend over and sit down comfortably. Subtract seven inches from this measure. Measure one inch less than half this amount and apply it along line AC, measuring from A down and marking point I. Mark point N one inch more than half the remaining amount from B.
Draw a line at right angles from line AC at point I and draw a line at right angles from line BD at N. Measure in on line I an inch and a half and mark point J. Measure beyond point J three inches and mark another point. Draw a line from this last point to G which is the line GH on the diagram. Curve the front edge of the drawers out to point J as indicated by the solid line on the diagram.
On line N measure in one and one-half inches and mark point O. Measure beyond point O four inches and mark a point. Draw a line from this last point to L which is the line LM on the diagram. Curve the back edge of the drawers to point O, as indicated by the solid line on the diagram.
Mark point K three and one-half inches below I and point P the same distance below N and swing the lower edge line through these points touching point F.
Fig (85) The drawers pattern laid on the goods ready for cutting
If you want the drawers to lap at the center-front and center-back add extensions at the waistline beyond point G in front running into the line GJ. In the back allow the extension beyond point L running into the line LO.
Cutting Circular Drawers: The layout for the drawers is shown in Fig. 85. Note that the material is folded double crosswise. Mark around each pattern piece and cut with heavy shears as described in Lesson II.
Making the Circular Drawers: Before closing the seams, sew the lace edging to the bottom of each leg section. Next close the inside leg seams. (See Fig. 86.) French seams will give the best finish.
Join the front and back facing pieces, mak
Fig. (86) French seam the leg joining
Fig. (87) Make a plain seam in joining the two pieces of the facing
ing an open seam, as in Fig. 87. Then lay these facing pieces along the crotch edge of the drawers on the right side of the garment and stitch a seam’s width back from the edge as illustrated in Fig. 88. Turn the facing onto the wrong side of the drawers, fold under the free edge three-eighths of an inch, press and stitch as shown in Fig. 89.
Fig. (88) Finish the crotch with shaped facings
Lap the two drawers sections at the front. Then sew on the belt at the top as you did the facings. The Fig. 90 shows the belt laid on the wrong side of the garment and stitched across the top, while Fig. 91 shows
Fig. (89) The facings stitched the second time
the belt turned onto the right side of the drawers, the raw edges turned in and the lower edge stitched in place.
Fig. (90) Face the top of the drawers
At the back lap the drawers the desired amount and finish with buttons and buttonholes as in Fig. 92.
Fig. (91) The facing turned the wrong side and stitched a second time
Should your pattern have fullness across the back, finish the front of the drawers with a deep facing and the back with narrow bias casings as shown in Fig. 93. The tapes which are inserted in the casings are sewed securely to the front facing before the casings are stitched on.
Fig. (92) Drawers that have a lap-closing in the back
Fig. (93) Sometimes the top is finished with a draw string
![](http://upload.wikimedia.org/wikipedia/commons/thumb/8/81/A_complete_course_in_dressmaking%2C_%28Vol._3%2C_Underwear%29_%28IA_completecoursein03cono%29_%28page_68_crop%29.jpg/250px-A_complete_course_in_dressmaking%2C_%28Vol._3%2C_Underwear%29_%28IA_completecoursein03cono%29_%28page_68_crop%29.jpg)
Fig (94) Circular drawers do away with bulky fullness at the top
Fig. 94 shows the finished drawers.
Making Step-in-Drawers Pattern: As the name implies, step-in drawers are constructed similar to the lower part of a step-in chemise. A pair of step-in drawers of batiste or light silk, as shown in Fig. 95, are especially nice for warm weather. There’s another point in their favor, too. They are easy to iron.
Fig. 96 shows the diagram for making them. them. Draw the line AB one inch longer than the measure from the waistline in the front to the waistline in the back, passing the tape between the legs as described before.
Draw line AD at right angle to line AB. Also draw line BC at right angle to AB. From A to D should measure half the width you
![]() |
![]() |
want the drawers to measure across the front or the back at the lower edge.
Mark point G three inches in from D. Also mark a point one inch down from A and draw the waistline in front from G to last point. Mark point R three inches in from C.
Locate center between lines AD and BC. Then draw line EF one-half inch nearer line AD which is the top. Draw lines JKI and LMN one and one-half inches either side of line EF. Mark points J and L one and one-half inches from line AB. One inch beyond mark the points K and M. Curve the line from K and M to the center line. Draw lines from G to I and from R to N. Mark points H and P two inches above points I and N and curve the sides of the drawers from these points to the lines IK and NM.
The curves on the front and back of the drawers ought to exactly match, so draw the curve on the front first and then put a piece of paper under the diagram and trace this portion of the pattern. Cut out the traced piece and use it as a guide in marking the curved edge on the back.
Measure down on the line RP one inch and curve the waistline in the back as indicated.
In tracing off the pattern allow seams at the top sides and lower edges. The center-front and center-back edges are placed on the fold of the goods.
Fig. (97) Envelope drawers are easy to make and easy to launder
Fig. (98) Diagram for making step-in drawers pattern
In making the step-in drawers leave the side seams open about six inches up. French seam the sides and finish the lower edges with a facing or lace.
Make a casing at the top as described in finishing the lower edge of the camisole.
Making a Pattern for Envelope Drawers: Another suggestion for summer drawers is shown in Fig. 97. These are envelope drawers.
You can make a practical pattern by cutting off the lower part of your envelope chemise pattern or make a diagram as shown in Fig. 98.
If you are working out a new diagram for the front of the drawers, draw the line AC one inch longer than you want the drawers in the front and line AB the width you want the front of the drawers, bringing this line out at right angle to line AC. Complete the right angle box by drawing the lines BD and CD.
Mark point E three inches in from B and point F one and a half inches up from the lower edge. Curve the waistline from a point one inch below A to E and draw the side from E to F. Swing in the lower edge from C to F.
In making the back, draw line BH one inch longer than line AC on the front diagram. Make line AB on the back diagram the width you want the back of the drawers. Complete the box by drawing line AC parallel to BD and line GH parallel to line AB.
Mark point E three inches from A and point F one and one-half inches from G. Draw line EF and on line E mark a point one inch below the top line. From this point draw the waistline. Draw line CD parallel to line GH and the distance below it that corresponds to the length of the strap on the envelope chemise. Then draw in the strap as indicated by the line JF.
In tracing the pattern allow seams at the outer edges. Only the center-front and center-back will be laid on the fold.
In making the drawers, use French seams at the sides. The lower edges and strap can be finished the same as the envelope chemise was finished. Make a casing at the top and insert elastic, as described previously in this lesson.
To Make a Bloomer Pattern: The construction of the bloomer shown in Fig. 99 is quite similar to the circular drawers. You will need to take two measurements before you make the pattern.
First take the length in the front from the waistline to the knee. This gives you the actual measure for your pattern as the lower edge of the bloomer frill ought to come just to the knee. Also take the crotch measure, as described in making the circular drawers.
In making the pattern (see Fig. 99a), draw the line AC about fifteen inches longer than
Fig (99) Bloomer completed
half the waist measure. Draw lines AB and CD at right angle to AC, and three inches longer than the length of front. Measure down on the line AB three inches and mark point E. At point E draw a line at right angle to line AB. On this line mark a point four inches from E which is point F on the diagram. Measure in five inches from C on the line AC and mark point G. Curve a line from F to G as indicated on the diagram. This is the waistline, and will of course have fullness in it.
Draw a diagonal line from G to the line CD three inches more than half the crotch measurement. (See line GH on the diagram.) Measure from D to H and mark point I the same distance from B that H is from D. Draw the front line from F to I.
Fig. (99a) Diagram for bloomer
Now apply the length that you took from the waistline to the knee in the front. From E to B ought to equal this measure. Draw the line BD parallel to pattern AC. Mark point J one and one-half inches from point B and point K an equal distance from point D. Then draw the side lines IJ and HK.
Allow a hem at the bottom and seams on all other edges in tracing off the bloomer pattern.
Cutting the Bloomers: The Fig. 99b shows the pattern laid on the material folded double crosswise. Mark around the pieces and cut as described in Lesson II.
Fig. (99b) Bloomer pattern laid on material
To Make the Bloomers: Join the inner leg seams first.(See Fig. 100.) If you are working on thin material make French seams. In heavy material such as flannel make open seams and overcast them.
Next join the crotch seam, making a French seam in thin material or an open seam, overcast, in heavy goods. Join the two pieces for the crotch facing, making an open seam. Turn the bloomers wrong side out, pin the facing in place, folding under the raw edges and stitch as shown in Fig. 101.
Finish the top of the bloomers with a bias casing. Cut the bias for the casing one and one-half inches wide. Stitch the casing to the top just as described in stitching the bias casing to the bottom of the camisole, only in this case make the casing a little wider. Three-quarters of an inch finished is a good width.
Fig. (101) Reinforce the crotch
Insert half-inch wide elastic cut to fit the waistline snugly plus a lap. Fasten the elastic the same as described in the camisole.
Turn a hem at the bottom of each leg section. Then stitch a bias casing directly above each hem. Cut the bias for each casing one inch wide and just long enough to go
around the leg section, plus seams at either end. Turn under all the raw edges and press the bias strip. Stitch it in place as shown in Fig. 102. Insert one-quarter inch wide elastic, cut the length that will fit around leg comfortably, plus a lap. Fasten the ends as described in the camisole.
Fig (102) Stitching on the casing
Making a Nightgown Pattern: When you think of the way you made a bungalow apron pattern, a nightgown pattern won’t seem a difficult task. You see, it’s just a matter of using your foundation waist pattern again. You can vary the style as much as you like.
If you want to copy the gown with the little sleeve cap shown in Fig. 103, draw a straight line on your paper and place your foundation waist pattern with the center-front and center-back edges along this line, with the edges just touching at the neck. Trace around the patterns, remove them and use the traced outline as a diagram. (See Fig. 104.)
Draw a line at right angles to the center-front and center back which will touch the front and back at the neck. This will give you the center of the sleeve cap. Draw your foundation lines at the armhole as described
![]() |
![]() |
in making the bungalow apron. This gives you the line CD. If you want the sleeve cap just across the top of the arm, measure in on the line about two and one-half inches and draw lines GF and HE. Measure out on the line AB about one and one-half inches beyond line CD and mark point I. Swing the curve for the sleeve cap from H to G touching point I. In tracing the pattern trace from C to H, from H to C, from I to G and from G to D. The other lines are foundation lines.
Complete the skirt part of the gown as described in making the bungalow apron in Lesson II. Draw in the neck outline in any desired shape.
Cutting the Nightgown:The layout, Fig. 105, shows the pattern placed on the material folded double lengthwise. Mark around the pattern pieces carefully and cut as described in Lesson II.
Making the Nightgown: Run a stay thread around neck to prevent stretching as described in chemise.
Finish neck and sleeves of the nightgown with lace edging. French seam the underarms (see Fig. 106) and turn hem at bottom as in Fig. 107.
Fig. (106) French seam the underarm of the nightgown
Fig. (107) Turning the hem at the lower edge
Making a Pattern for a Yoke Nightgown: One of the many possible variations is shown in Fig. 108. You can use your foundation waist pattern in making your yoke nightgown, too. This is the way to do it:
Lay your pattern on another piece of pattern and trace around it as described before. Mark the yoke outline on these diagrams, as shown in Fig. 109. You can bring the point anywhere you desire on the shoulder or make it lower or higher in the neck. All you must be careful of is that the front and the back match.
Be sure that the point on the shoulder comes the same distance from the neck in both the front and back. Also be careful that the lower edge comes the same distance from the armhole on the front and back at the underarm seam. Gather straight pieces to the bottom of the yoke for skirt portions.
The edges of such a yoke is attractive finished with narrow beading.
Making a Petticoat Pattern: You can copy all sorts of petticoat and skirt styles with a foundation skirt pattern. You can use any six or seven gored skirt as a foundation block pattern.
Fig (109) Using a block pattern to make a nightgown yoke
If you want to copy a flounced petticoat as shown in Fig. 110, place your foundation pattern with the gores even through the lower part and trace around them. Remove the pattern and use the traced outline as a diagram. (See Fig. 111.)
You will want fullness in the top of your pattern, so mark across the darts. When you trace the new pattern pieces, leave the darts in. Mark a seam at the side from the center of the dart at the top to the bottom of the skirt along the old side seam. This is the only seam you will need in the new pattern. Measure up an even distance all the way around for the top of the flounce. (See dotted line in diagram.)
Put another piece of paper under the diagram and trace the upper front of the petticoat tracing along the center front, the top and the side seam from the center of the dart. Allow seams at the side, top and bottom. Trace the back piece in the same way.
Measure along the dotted line. Make the flounce for the whole petticoat three times this amount. Make it the depth from the dotted line to the lower edge of the diagram plus a seam at the top and a hem at the bottom. A style such as this might be made in sateen, taffeta silk or cotton jersey, or muslin with a ruffle of embroidered flouncing, or batiste, wash satin or crepe de chine with flounce of lace.
Cutting the Petticoat: Fig. 112 shows the pattern laid on the material folded lengthwise. In this case the ruffles are cut lengthwise. It is well to remember that a ruffle that is cut crosswise always appears much fuller and flares out more than one cut lengthwise.
Making the Petticoat: Finish the placket at the left side front first. It is easier to handle a single piece than it is a whole petticoat after it is made up. A continuous facing makes the best finish for a slashed placket.
For a continuous facing, cut the material two and one-quarter inches wide and one-half inch longer than twice the depth of the placket. This will make a facing three-quarters of an inch wide finished.
Slash the petticoat and place the facing on the wrong side of the petticoat with the edge of the facing even with the edge of the material at the top of the slash, but with the facing extending nearly a seam’s width beyond the edge of the slash at the bottom. Stitch down one side of the slash and up the other, keeping the stitching a seam’s width in from the edge of the facing. Turn under the free edge of the facing a seam’s width, fold the facing through the center and stitch the free edge over the raw edge on the right side. (See Fig. 113.)
On the front side of the slash fold back the facing toward the front of the garment and pin
Fig. (113) Finishing the placket with a continuous facing
it in place. When the garment is finished the facing on the front edge of the slash laps over the facing on the back edge of the slash.
Close the side seams in the petticoat and join the pieces in the flounce making French seams.
Finish the top of the petticoat with a bias casing, cutting the bias one and one-half inches wide and finishing the casing three-quarters of an inch wide. Stitch the casing as described in the camisole. The Fig. 114 shows the casing as it is stitched at the placket.
Fig. (114) The way the facing turns when the waist band is on
Insert one-half inch wide elastic cut to fit waistline snugly before stitching across ends of casing and elastic several times to fasten elastic securely. Fold flounce in half, slashing the material with the points of the shears to the depth of one-quarter of an inch at center-front and center-back. (See Fig. 115.) Then fold the flounce again as in Fig. 116 and slash the new
![]() |
![]() | |
Fig. (115) Fold the flounce in half | Fig. (116) Determining the four equal parts of the flounce |
creases at the top as before. Run in four gather threads at the top—a gather thread between each two slashes. Draw up the gather threads until the flounce will just fit the bottom of the petticoat, keeping the spaces between the slashes in the top of the flounce equal.
Place flounce over petticoat with right sides of the material together and gathered edge of flounce even with lower edge of petticoat. Cut a bias strip of the material three-quarters of an inch wide. Place this along the lower edge over the flounce. (See Fig. 117.)
Stitch around the lower edge of the petticoat, running the stitching a seam's width back from the edge. Turn the flounce down
![]() |
![]() |
into its finished position. Cut off all but about an eighth of an inch of the seam at the joining of the flounce and petticoat on the wrong side, fold under the raw edge of the bias strip and stitch it flat over the raw edges of the seam as shownFig. (119) Ball and socket snaps make a neat petticoat closing in Fig. 118.
Finish the placket with ball and socket snaps. These lie flatter than hooks and eyes or buttons. (See Fig. 119.)
Making the most of Lesson III: Read the lesson through, then go back and study each subject separately. After you have read one subject, lay the lesson aside and think about it. Run over it in your mind and see if you understand it thoroughly.
Make the diagrams with the help of the lesson. Then close the book and see if you can draft one of the diagrams without referring to the book. Keep on practicing until you are able to make the diagrams by yourself.
As you study each subject think how you can apply the same knowledge to making other kinds of garments.